This pair of CineMilled All-Terrain Shoes for Gimbal Ring Feetfrom CineMilled All-Terrain Shoes for Gimbal Ring Feetallows you to safely set your gimbal ring down in any environment. The All-Terrain Shoes connect to the CineMilled Gimbal Ring Feet (sold separately). Once attached to the feet, you can set your gimbal ring down in all kinds of terrain, including sand, snow, or soft dirt. The All-Terrain Shoes can be mounted in 3 different positions, allowing you to position the ring to best suit your needs. Installation screws to attach the shoes to the feet are included.

Attach to CineMilled Gimbal Ring Feet    Set Gimbal Ring Down in Any Environment    Works with Snow, Sand, and Soft Dirt    Installation Screws Included

Related Questions and Answers

Q: 1. What is the diameter of the handles? I'm hoping to buy attachment accessories for it.

A: The diameter of this handle is not listed, however you will be able to attach the Impact Atom Clamp with Ratchet Handle, B&H # IMME100, to this product. From there you will have a 1/4"-20 and 3/8"-16 thread for accessories. https://bhpho.to/2p3lC2X

Q: 2. Can I use my Zhiyun Crane with this halo?

A: According to Glide Gear: The Glide Gear Gimbal Halo allows you to attach any single arm gimbal with a 1/4 20 mounting screw. It increases stability with 2 hand use, reduces arm fatigue and allows the ability to attach accessories. Since the Zhiyun-Tech Cranes have a 1/4 mount in the base their handle you are good to go.

Q: 3. Would it be possible to use this with a Ronin-S in a primarily right side up scenario instead of the displayed 'low mode' and use an Easyrig to hold it between where the two feet are?

A: Not that we are aware of. This system is designed to hold the gimbal in an under-slung position only.

Q: 4. Would I have to purchase the bracket to mount my Original Ronin separately or does it already come with one? Need to know this before I buy?

A: No. The unit will work with any gimbal and we have mounts for the Freefly MōVI, DJI Ronin(+M/MX) and Tilta Gravity Gimbals. Please review the following mounting plate CineMilled Quick-Switch Mount Plate for DJI Ronin BH #CICM401 • MFR #CM-40 https://bhpho.to/3EnbYf4

Q: 5. Hi,I have some Canon 600EX-RT's that I'd like to use with this bar. Can flashes be mounted beneath the bar so that they hang upside down? Basically, I want two on top and two on the bottom.

A: Yes, flashes can be mounted while hanging below the bar. The Mounts can be unscrewed and put on upside down. Either way though, you want to make sure that you use both the hotshoe's tightening screw and the flash's tightening screw to keep it secured. If you only screw down one of your fasteners, then there is still a chance that the flash could fall out of the hotshoe. (We found that out the hard way.)

Q: 6. I would like to oder this Pro-Ring system with the Cinemilled feet and Ready Rig Spindals. I cant find these in the accessories you offer. Can you help me out?

A: Following is a link to the Cinemilled Spindle Mount https://bhpho.to/2Gjaslr and the link to the Cinemilled Feet for Gimbal Ring - https://bhpho.to/3inGQjK along with the All-Terrain Shoes for Gimbal Ring Feet https://bhpho.to/33nV53Z

Q: 7. Are the grips and feet included in this price?

A: The CineMilled PRO-Ring 14 x 14" Handlebar comes with 4 “corners”, 4 tubes 14″ long each, and 2 foam grips. No feet are included.

Q: 8. Will it work with Leofoto LN-324C?

A: Yes the Leofoto Set of 3 Spikes with Snow Shoes is compatible on the Leofoto LN-324C. The feet on the tripod come off and are 3/8 inch and the snow shows are 3/8 inch as well.

Q: 9. What would be the height of these when installed?

A: The exact height is not listed. However these are shoes which are very thin. They are going to be only a matter of a few millimeters tall. They are not going to make much of a difference in the height of the product.

Q: 10. Can I use this with my Ronin SC Gimbal..? Thanks.

A: Yes, any single arm gimbal with a 1/4 20" thread at the bottom will mount on this device.