Designed for large venues, the 120V Da-Lite 29208G Wireline Advantage 78x139" Motorized Screen 120Vuses thin steel cables instead of black drop to lower the screen to an appropriate viewing height. Once the screen is installed, the screen's trim conceals the rough opening in your ceiling, eliminating the need to complete additional trim work. Sliding installation brackets help make it easy to attach the screen housing to the structure above the drop ceiling.

159" Diagonal / 16:9 Aspect Ratio    HD Progressive 1.3 Surface    1.3 Gain / 150° Viewing Angle    Suspended from Cable up to 29'    Slim-Tab, Low-Profile Tab-Tensioning    Hand-Held Remote Included    Built-In Radio-Frequency Motor    Seamless, Black-Backed Screen Surface    Flangeless Case

Ideal for applications where projector brightness and screen size require an increase in gain, the white surface offers high-fidelity color reproduction, and allows for more flexibility with ambient light conditions. This surface works for video as well as charts and graphs in a corporate setting. Cone 150° Gain: 1.3

• Up to 29' of cable to accommodate appropriate viewing height in rooms with high ceilings
• Slim-Tab, a lower profile and stronger tab design to keep your screen taut
• Tensioning Cable System to prevent warping and ensure even lateral tension
• UL Plenum-rated case
• Works with separately available radio-frequency control accessories such as a single-channel wall switch, dry contact interface, and RS-232 interface
• Black-backed screen material for enhanced image quality and opacity
• Seamless screen surface

Case does not have trim flange, making it suitable for non-ceiling-recessed applications.

Related Questions and Answers

Q: 1. what is the length of this lamp?

A: Maximum Overall Length (MOL)3.75" / 9.52 cm

Q: 2. what is the dimension (inch) of the bulb?

A: around 1.75

Q: 3. Can we find these in stores

A: I am a lighting distributor, and purchased from B&H because of the ease, I wouldn't have to make a minimum qualifying order on an item that doesn't have high volume. Old fashioned camera stores kept lamps like this for projectors, but B&H is my choice. Lamps are broken so often in shipment I don't deal with companies I cannot depend on for service.

Q: 4. Can you put this 500w bulb into a 420w Pepper light?

A: Although this 500 watt bulb can fit, it is not recommended for use with the LTM Pepper 420. A more suitable bulb is the Ushio EKB Lamp - 420 watts/120 volts, B&H # USEKB. https://bhpho.to/395yPN1

Q: 5. Will this lamp fit in Kodak Medalist I Carousel projector? The unit says to replace with 120v 300w 60hz FHS lamp only

A: I have a Kodak Carousel 650H in which I use the subject lamps. I have recently bought 5 of them as back-up.

Q: 6. I need four.

A: Buy Four if you need four! i have several spares because i drop them and knock my light stand over.

Q: 7. Is the Impact ELH lamp ok for use in a Kodak Carousel 760H Projector. If not, what lamp would you recommend?

A: From all I have found on the internet, the ELH lamp is suitable for the Kodak 750, 760, 860 projectors. I bought this bulb for an 860H and it works just fine. Hope this helps.

Q: 8. Will this work for the Profoto D1?

A: Yes this Ushio DRA is compatible with the Profoto D1.

Q: 9. Is the color produced by this bulb orange or white?

A: The color temperature of the EMD lamp is 3200k, which means that it is tungsten-balanced rather than daylight-balanced.

Q: 10. what is the length between the two pins?

A: 5mm center to center.