Designed for large venues, the 220V Da-Lite 29452E Wireline Advantage Motorized Projection Screenuses thin steel cables instead of black drop to lower the screen to an appropriate viewing height. Once the screen is installed, the screen's trim conceals the rough opening in your ceiling, eliminating the need to complete additional trim work. Sliding installation brackets help make it easy to attach the screen housing to the structure above the drop ceiling.

188" Diagonal / 16:9 Aspect Ratio    Dual Vision Surface    0.9 Gain / 130° Viewing Angle    Suspended from Cable up to 29'    Slim-Tab, Low-Profile Tab-Tensioning    Hand-Held Remote Included    Built-In Radio-Frequency Motor    Seamless, Black-Backed Screen Surface

Dual Vision is a flexible vinyl surface ideal for rear projection, but capable of front projection as well. Dual Vision is ideal for video projection under controlled ambient light conditions. With a wide viewing cone and light gray tint, a sharp image with no color shift is observed regardless of location in the room. Cone: 130° Gain: 0.9

• Up to 29' of cable to accommodate appropriate viewing height in rooms with high ceilings
• Slim-Tab, a lower profile and stronger tab design to keep your screen taut
• Tensioning Cable System to prevent warping and ensure even lateral tension
• UL Plenum-rated case
• Works with separately available radio-frequency control accessories such as a single-channel wall switch, dry contact interface, and RS-232 interface
• Seamless screen surface

Related Questions and Answers

Q: 1. Godox BLP LED Projection Attachment for Bowens I can use it in godox sl 60llBi ?

A: Yes. The Godox BLP LED Projection Attachment for Bowens can be used with the Godox SL60IIBI Bi-Color LED Video Light via the common Bowens Mount that they both share.

Q: 2. Compatible with A7siii and raw recording?

A: The a7s III raw video can only be recorded with an external recorder. The Delkin Devices 1TB Advantage UHS-I SDXC Memory Card will work for raw still images.

Q: 3. Will this fit on the DLED 2.1 as well? Their videos show a DP1s is this the same?

A: The B&H page that describes the DLED 2.1, in the Acessories section, lists the DPS1 as the recommended imager for the DLED 2.1.I use the MDLH4 with the DP 1.1 imager and the 85 mm 2.8 lens. As far as I can tell there are only single versions of the lenses for all their imagers, which makes perfect sense.Alternatively, if you have a Leitz slide projector, the Leitz projector lens will fit BUT without the safe travel groove on the lens AND with the danger of an indent mark on the lens if over tightened.The imager and lens combination works really well. I also use the iris diaphgram attachment to control the light spread - it all works beautifully well with my macro projects.(The iris control lever has quality issues - it is loosely glued rather than screwed in - and should never be used to remove the diaphgram from the imager. Instead, loosen the attachment tightening screw on the imager and push from the bottom. This is not in any Dedo information.)

Q: 4. Does this attach directly to the ad400 pro?

A: The Godox BFP Flash Projection Attachment for Bowens has a Bowen-S connector. You can connect this light modifier to the Godox AD400Pro Witstro All-in-One Outdoor Flash with the Bowens Mount Adapter Ring included in the box with the flash.

Q: 5. Dear All, how close to the back ground wall can it be placed? Thanks

A: How close this lens can be placed in relation to a background wall would be dependent on the type of lighting being used. For example, if this lens was used with one of the Dedolight DLH4 Tungsten Lights, that would produce a greater amount of heat versus using the lens with a Dedolight DLED4.1 LED Light.

Q: 6. What is the focal length of the included lens?

A: The Godox BFP Flash Projection Attachment for Bowens comes with an 85mm lens.

Q: 7. Can I attach it to DLH4 light head directly? Do I need any other accessories for using it?

A: It attaches directly to the front of the HLH4 housing; just ahead of the filter slot, and is locked in by the same rotating top clip that locks the filter in place.

Q: 8. Would this work well for shooting on the BMPCC 4k?

A: Delkin Devices 1TB Advantage UHS-I SDXC Memory Card BH #DEDDSDW633 has a Max Read Speed: 100 MB/s, Max Write Speed: 80 MB/s and min Write Speed: 30 MB/s which is slow if you want to record at 4K60.

Q: 9. I would like to find a similar projector to fit elinchrom 600w studio lights. Ideally with optional metal leaves to control the area to be lighted. Does anyone have any recommendations?

A: Please review the following item. https://bhpho.to/3pEq4Us

Q: 10. Is the speed ring interchangeable? If so, what size is it?

A: The speedring that is part of the Godox BFP Flash Projection Attachment for Bowens is not interchangeable.