Designed for large venues, the 220V Da-Lite 29459EG Wireline Advantage Motorized Projection Screen 220Vuses thin steel cables instead of black drop to lower the screen to an appropriate viewing height. Once the screen is installed, the screen's trim conceals the rough opening in your ceiling, eliminating the need to complete additional trim work. Sliding installation brackets help make it easy to attach the screen housing to the structure above the drop ceiling.

133" Diagonal / 16:9 Aspect Ratio    Dual Vision Surface    0.9 Gain / 130° Viewing Angle    Suspended from Cable up to 29'    Slim-Tab, Low-Profile Tab-Tensioning    Hand-Held Remote Included    Built-In Radio-Frequency Motor    Seamless, Black-Backed Screen Surface    Flangeless Case

Dual Vision is a flexible vinyl surface ideal for rear projection, but capable of front projection as well. Dual Vision is ideal for video projection under controlled ambient light conditions. With a wide viewing cone and light gray tint, a sharp image with no color shift is observed regardless of location in the room. Cone: 130° Gain: 0.9

• Up to 29' of cable to accommodate appropriate viewing height in rooms with high ceilings
• Slim-Tab, a lower profile and stronger tab design to keep your screen taut
• Tensioning Cable System to prevent warping and ensure even lateral tension
• UL Plenum-rated case
• Works with separately available radio-frequency control accessories such as a single-channel wall switch, dry contact interface, and RS-232 interface
• Seamless screen surface

Case does not have trim flange, making it suitable for non-ceiling-recessed applications.

Related Questions and Answers

Q: 1. I have a Pentax K3II and a Sigma 610 DG Super flash. I want to know how to do to be able to connect a flash strobe kit through a radio trigger. Which ones would be compatible for my K3II in order to be able to make the strobes functional and, if possible, also to use the Sigma? What do you recommend buying in addition to this kit?

A: I would recommend purchasing the Vello FreeWave LR Kit with 2 Receivers, B&H # VERFWLRK, for your usage needs. The Impact Two Monolight Kit (220V), B&H # IMEX100A2LKX, has a 1/8 (3.5mm) miniphone sync terminal on the rear of the strobe monolight. The Vello FreeWave LR Kit comes with a miniphone to miniphone cable, so you may connect the Vello FreeWave LR receiver to the Impact monolight. The receiver also has a hot shoe on the top of the unit, onto which you may mount the Sigma EF 610 DG Super Flash. As the kit I listed above comes with two receivers, you may connect one receiver to the Sigma EF 610 DG Super Flash, and one to one of the monolights in the Impact monolight kit. As the Impact monolights have built-in optical slaves, the unit without the Vello receiver will trigger when it sees the light output from the light fixture with the receiver. Do note the output of the Sigma EF 610 DG Super Flash will have to be set manually when using this setup. There is no option that will work and retain TTL automatic flash capability with this setup.

Q: 2. Are these lights tungsten or daylight ( 5500K). Can I use my Nikon on auto white or have to balance?

A: Strobe lights are typically daylight-balanced. You would either use the daylight-balanced or flash-balanced white balance preset on your camera, or you would use the Custom White Balance setting to set a custom white balance. Auto White Balance is not recommended for strobe usage.

Q: 3. My flash tube broke. Is that covered in the one year warranty ?

A: Unfortunately, the warranty for this monolight only covers defects in the unit as a whole. It does not cover lamps.

Q: 4. Does this light unit have a slave so that both lights flash at the same time?

A: Both lights do. Each plugs into the wall separately and a supply synch cord plugs ininto one of thelights you chose. When the shutter goefires that light and the other light fires through the slave trigger works greats the light plugged into the one light

Q: 5. How hot do these lights get? What gloves would be sufficient protection?

A: This is a typical hot light. You will want leather gloves - or at least good heavy cloth work gloves if you need to handle this after it has been on for a few minutes and for at least up to about 20 minutes after it is shut off.

Q: 6. I got my Arri 650 plus today, and when i turn the focus knob, it seems that it turns off the light if i turn it all the way left, or all the way right. is that supposed to happen? it feels like the knob is a bit sensitive too. thanks

A: No, this certainly shouldn't happen. Perhaps there's something amiss with the wiring. I suggest taking back for a review or simply exchanging for another.

Q: 7. I have set this up and use an on-camera flash to trip the two lights BUT I am NOT able to vary the output of the flash. I dial from full to 1/8 but only the modeling light varies in intensity. Am I doing something wrong?Lucian

A: Just to be sure - when reducing flash power, you must dump the flash first and then measure power. This means if the flash is at full power and you reduce it to an 1/8, you must first fire a flash to dump the power out of the flash capacitors and reduce their charge to an 1/8 and then measure your flash output. If the flash remains at full for a 3rd and 4th shot, then it may be faulty.

Q: 8. Does it have a dimmer?

A: No, there is no dimmer attached. You may wish to purchase one separately.

Q: 9. In the list of accessories included with this kit theres a Dedicated EX100A SpeedringCan this speedring be used with softboxes made by other softbox manufacturers?

A: Unfortunately, the speed ring included in this kit would be limited to use with the included softboxes.

Q: 10. I have a Nikon D3300, Do I need to buy the PowerTrigger transmitter in order to make the Flash work? Or the sync cord will do the job.

A: I am not familiar with Nikon but I can tell you that the sync cord works with my Canon DSLR. As long as there is an outlet on the side of the camera, which there should be, it should work fine.