Designed for large venues, the 220V Da-Lite 29265EG Wireline Advantage 65x116 Motorized Screen 220Vuses thin steel cables instead of black drop to lower the screen to an appropriate viewing height. Once the screen is installed, the screen's trim conceals the rough opening in your ceiling, eliminating the need to complete additional trim work. Sliding installation brackets help make it easy to attach the screen housing to the structure above the drop ceiling.

133" Diagonal / 16:9 Aspect Ratio    HD Progressive 0.6 Surface    0.6 Gain / 170° Viewing Angle    Suspended from Cable up to 29'    Slim-Tab, Low-Profile Tab-Tensioning    Hand-Held Remote Included    Built-In Radio-Frequency Motor    Seamless, Black-Backed Screen Surface    Flangeless Case

Ideal for high output projectors or applications where projector brightness and screen size require low gain, the gray surface compensates for a brightly lit environment so that image contrast is preserved. In low ambient light, HD Progressive 0.6 provides deep contrast and is typically used with video. Cone: 170° Gain: 0.6

• Up to 29' of cable to accommodate appropriate viewing height in rooms with high ceilings
• Slim-Tab, a lower profile and stronger tab design to keep your screen taut
• Tensioning Cable System to prevent warping and ensure even lateral tension
• UL Plenum-rated case
• Works with separately available radio-frequency control accessories such as a single-channel wall switch, dry contact interface, and RS-232 interface
• Black-backed screen material for enhanced image quality and opacity
• Seamless screen surface

Case does not have trim flange, making it suitable for non-ceiling-recessed applications.

Related Questions and Answers

Q: 1. does this come with a sync cord?

A: Yes the sync cord is included.

Q: 2. I got my Arri 650 plus today, and when i turn the focus knob, it seems that it turns off the light if i turn it all the way left, or all the way right. is that supposed to happen? it feels like the knob is a bit sensitive too. thanks

A: No, this certainly shouldn't happen. Perhaps there's something amiss with the wiring. I suggest taking back for a review or simply exchanging for another.

Q: 3. Does it have a dimmer?

A: No, there is no dimmer attached. You may wish to purchase one separately.

Q: 4. Are there two lights included with this unit. Are the lights 5600K?

A: Yes, the kit comes with two Impact One Monolights. They are strobe type lights and are daylight rated.Note the camera you use this with needs to have a sync port or you will need to get an adapter or wireless sync.And this is made for still photos not video.

Q: 5. I have a Pentax K3II and a Sigma 610 DG Super flash. I want to know how to do to be able to connect a flash strobe kit through a radio trigger. Which ones would be compatible for my K3II in order to be able to make the strobes functional and, if possible, also to use the Sigma? What do you recommend buying in addition to this kit?

A: I would recommend purchasing the Vello FreeWave LR Kit with 2 Receivers, B&H # VERFWLRK, for your usage needs. The Impact Two Monolight Kit (220V), B&H # IMEX100A2LKX, has a 1/8 (3.5mm) miniphone sync terminal on the rear of the strobe monolight. The Vello FreeWave LR Kit comes with a miniphone to miniphone cable, so you may connect the Vello FreeWave LR receiver to the Impact monolight. The receiver also has a hot shoe on the top of the unit, onto which you may mount the Sigma EF 610 DG Super Flash. As the kit I listed above comes with two receivers, you may connect one receiver to the Sigma EF 610 DG Super Flash, and one to one of the monolights in the Impact monolight kit. As the Impact monolights have built-in optical slaves, the unit without the Vello receiver will trigger when it sees the light output from the light fixture with the receiver. Do note the output of the Sigma EF 610 DG Super Flash will have to be set manually when using this setup. There is no option that will work and retain TTL automatic flash capability with this setup.

Q: 6. I was just wondering if anyone has replaced the modelling lamp with an LED light bulb? I imagine you could get a lot more light output from an LED bulb, especially a cree bulb. I understand it would have to be the dimmable variety...

A: It has not been tested by the manufacture. It is not recommended to do that as you can damage the electronics if there is a compatibility issue.

Q: 7. I have set this up and use an on-camera flash to trip the two lights BUT I am NOT able to vary the output of the flash. I dial from full to 1/8 but only the modeling light varies in intensity. Am I doing something wrong?Lucian

A: Just to be sure - when reducing flash power, you must dump the flash first and then measure power. This means if the flash is at full power and you reduce it to an 1/8, you must first fire a flash to dump the power out of the flash capacitors and reduce their charge to an 1/8 and then measure your flash output. If the flash remains at full for a 3rd and 4th shot, then it may be faulty.

Q: 8. Hi, which exactly is the Mini to PC Synch Cord? Could you send me a link?I have a canon 650D and i'm not pretty sure if i can manage these lights from my camera.Thanks.

A: A mini to PC sync cord would allow a camera with a sync terminal to be connected to these lights. Please see the following link for an example of the cable: a href= http://bhpho.to/1qtaQvJ. target= _blank http://bhpho.to/1qtaQvJ./a As for use with the Canon 650D, you would need a hotshoe to PC sync adapter to use these monolights. Please see the link for the adapter: a href= http://bhpho.to/1jT4Cko target= _blank http://bhpho.to/1jT4Cko/a

Q: 9. Will this strobe work with 3rd party modifiers, or only the supplied softboxes?

A: That model strobe uses the Elinchrom mount also called EX. There are a few different manufactures that make modifiers with that mount, Elinchrom, Impact and Interfit. Note to be careful when picking it out that it is the correct mount. Impact and Interfit make different mounts not just EX.

Q: 10. How hot do these lights get? What gloves would be sufficient protection?

A: This is a typical hot light. You will want leather gloves - or at least good heavy cloth work gloves if you need to handle this after it has been on for a few minutes and for at least up to about 20 minutes after it is shut off.