Designed for large venues, the 220V Da-Lite 29268EG Wireline Advantage Motorized Projection Screen 65x116"uses thin steel cables instead of black drop to lower the screen to an appropriate viewing height. Once the screen is installed, the screen's trim conceals the rough opening in your ceiling, eliminating the need to complete additional trim work. Sliding installation brackets help make it easy to attach the screen housing to the structure above the drop ceiling.

133" Diagonal / 16:9 Aspect Ratio    HD Progressive 1.3 Surface    1.3 Gain / 150° Viewing Angle    Suspended from Cable up to 29'    Slim-Tab, Low-Profile Tab-Tensioning    Hand-Held Remote Included    Built-In Radio-Frequency Motor    Seamless, Black-Backed Screen Surface    Flangeless Case

Ideal for applications where projector brightness and screen size require an increase in gain, the white surface offers high-fidelity color reproduction, and allows for more flexibility with ambient light conditions. This surface works for video as well as charts and graphs in a corporate setting. Cone 150° Gain: 1.3

• Up to 29' of cable to accommodate appropriate viewing height in rooms with high ceilings
• Slim-Tab, a lower profile and stronger tab design to keep your screen taut
• Tensioning Cable System to prevent warping and ensure even lateral tension
• UL Plenum-rated case
• Works with separately available radio-frequency control accessories such as a single-channel wall switch, dry contact interface, and RS-232 interface
• Black-backed screen material for enhanced image quality and opacity
• Seamless screen surface

Case does not have trim flange, making it suitable for non-ceiling-recessed applications.

Related Questions and Answers

Q: 1. Will this fit on the DLED 2.1 as well? Their videos show a DP1s is this the same?

A: The B&H page that describes the DLED 2.1, in the Acessories section, lists the DPS1 as the recommended imager for the DLED 2.1.I use the MDLH4 with the DP 1.1 imager and the 85 mm 2.8 lens. As far as I can tell there are only single versions of the lenses for all their imagers, which makes perfect sense.Alternatively, if you have a Leitz slide projector, the Leitz projector lens will fit BUT without the safe travel groove on the lens AND with the danger of an indent mark on the lens if over tightened.The imager and lens combination works really well. I also use the iris diaphgram attachment to control the light spread - it all works beautifully well with my macro projects.(The iris control lever has quality issues - it is loosely glued rather than screwed in - and should never be used to remove the diaphgram from the imager. Instead, loosen the attachment tightening screw on the imager and push from the bottom. This is not in any Dedo information.)

Q: 2. Will this work with Godox continuous lights? I want to use it for adding texture to my backdrop for video.

A: The Godox BLP LED Projection Attachment for Bowens is recommended for LED continuous lights.

Q: 3. Can I attach it to DLH4 light head directly? Do I need any other accessories for using it?

A: It attaches directly to the front of the HLH4 housing; just ahead of the filter slot, and is locked in by the same rotating top clip that locks the filter in place.

Q: 4. Is this compatible with LED lights? If it is, what is the maximum power output LED light which it can handle?

A: The Godox BFP Flash Projection Attachment for Bowens BH #GOBFP was designed for studio flash.

Q: 5. Compatible with A7siii and raw recording?

A: The a7s III raw video can only be recorded with an external recorder. The Delkin Devices 1TB Advantage UHS-I SDXC Memory Card will work for raw still images.

Q: 6. Will this work with aputure units? Will it work with 600x/d/c?

A: The Godox BLP LED Projection Attachment for Bowens BH #GOBLP is designed for Bowens mount LED lights under 300w.

Q: 7. Is the speed ring interchangeable? If so, what size is it?

A: The speedring that is part of the Godox BFP Flash Projection Attachment for Bowens is not interchangeable.

Q: 8. I would like to find a similar projector to fit elinchrom 600w studio lights. Ideally with optional metal leaves to control the area to be lighted. Does anyone have any recommendations?

A: Please review the following item. https://bhpho.to/3pEq4Us

Q: 9. Does this attach directly to the ad400 pro?

A: The Godox BFP Flash Projection Attachment for Bowens has a Bowen-S connector. You can connect this light modifier to the Godox AD400Pro Witstro All-in-One Outdoor Flash with the Bowens Mount Adapter Ring included in the box with the flash.

Q: 10. Does it work with hive wasp?

A: This lens does not work on the Hive Wasp.