Rosco 8' Fluorescent Lighting Sleeve - Middle Lavenderare a very reliable and cost-effective system for easy control of tough lighting scenarios- especially under fluorescents. In addition to the financial benefits of the sleeves, they protect against the potential disaster of glass shattering by containing the lamp within the end caps.

Rosco sleeves are constructed of a solid polycarbonate tube within which is held the specific filter. The choice of filters and combination of filters is endless - there are complete Roscolux, Cinegel or E-Colour color filter lines - something for every venue, every photographer, every cinematographer.

For T12 Lamps    Over 300 Colors Available    UL94HB Rated Polycarbonate    End Caps Protect From Shattered Glass    Easily Trimmed with Scissors

Available in sizes for T12, T8 and T5 fluorescent lamps

The T8 and T5 sizes contain a UV filter that minimizes fading

All standard sizes (2, 4, 5, and 8') are easily trimmed to accommodate any size lamp

Related Questions and Answers

Q: 1. Why are three fixtures included, but only two stands? Also, are the lamps daylight or tungsten?

A: The description says there are three stands -- two 8-foot stands and one 9.5-foot stand. Taller one is for use with the included boom arm kit. Have you read the description?

Q: 2. Can I use it with Ronin RS3 Pro and Blackmagic Studio Camera 6K Pro?

A: The DJI RS3 Pro as well as the Blackmagic Design Studio Camera 6K Pro are both supported by the Middle Things APC-R Controller. However balancing a Blackmagic Studio 6K Pro camera on a RS3 Pro is not recommended, nor does DJI offically support it. We would suggest using a Blackmagic Design Pocket Cinema Camera 6K Pro instead for maximum compatibility. https://www.middlethings.co/apcr-support/

Q: 3. will this work with a Middle Atlantic TechPed 13x18 TP-F1318 ?

A: I'm guessing not as it's width is 19 . Standard rack mount size.

Q: 4. How wide is the cable shelf sticking out the back?

A: The cable shelf on the Middle Atlantic Brush Grommet Panel BR2 is just under 3 inches.

Q: 5. It "protects the front." Not the back?

A: The Apple Smart Cover for iPad does not apply to the rear section of the iPad. That part of the iPad remains exposed. The Apple Smart Cover for iPad only protects the front screen side as a result.

Q: 6. will this hold a small color laser jet printer?

A: The shelf is 32.0 x 12.0 and can hold 50lbs. Most small laser jet printers are under 50lbs, and if the printer fits in that footprint then it's good.

Q: 7. Does this work with raven eye?

A: No, the Middle Things Middle Remote for Gimbals & Cameras is designed for the units shown below: Blackmagic Design ATEM Switchers Blackmagic Design Pocket Cinema Cameras Blackmagic Design URSA Cameras DJI Ronin Series Gimbals

Q: 8. How many server can we put on this

A: There are 37 RU of space on this rack. For servers or components that generate a lot of heat, it would be recommended to leave some space between each item, or even to use exhaust panels like # ACAICP2L to provide better cooling. Please chat with us, send an e-mail, or call in by phone to discuss the specific needs of your setup.

Q: 9. Would a Kino truematch 3200k bulb work in these to get tungsten? - this product? BH #KI26SK32120

A: Yes they can be used.

Q: 10. Does this rack take cage nuts or cage clips to install equipment on the rails? I see the rails have slight circular threads in them but is that enough to house equipment with a standard 10-32 screw or are cage nuts needed?

A: This rack comes standard with (2) pairs of 11-gauge threaded, 10-32 rackrails with EIA spacing and labeled rackspace increments. Electrical knockouts on rear plates (both top and bottom) can easily be removed to pass cables (includes 1/2", 3/4", 1" and 1-1/2" openings). The configurable, open top also includes a UHF/VHF knockout. Pre-Installed Washers Pre-installed washers on all 10-32 threaded rackscrews save installation time. Cabinet Accepts 19" Equipment (Width) Depth 24" Capacity 64-3/4" (37U)