The Redrock Micro microRemote Wireless Kit SLS Motor flexCablefrom Redrock Micro microRemote Wireless Kit SLS Motor flexCableis designed to help control your camera focus while using stabilizers such as Steadicams, Jib Arms, and Gimbal Stabilizers. By controlling focus wirelessly you remove the need to directly touch the camera during a shot, but still control focus to direct your viewer's attention.

In situations where wireless may not be possible, the optional tethering cable wires the microRemote for direct, interference-free operation up to 20 feet away.

Wireless Focus Control    Wireless Hand Controller with Hard Stops    SLS Motor Fits on 15mm Rod    SLS Motor Weighs only 4.23 Ounces    Good for Stabilizers and Handheld Rigs    Wireless Basestation Included    Lightweight, Thin flexCable for Power    Disk-Marking Pencil, 2 x AA Batteries

This Handheld Controller features the ability to trigger the Run/Stop of supported cameras (cable required). This allows for control of the camera remotely for when it may be inaccessible. The microRemote Handheld Unit also has a built in Run/Stop light that indicates when the camera is recording or not, so the camera does not need to be within your line of sight.

All lenses are mapped to the full 270° rotation of the microRemote. This is especially helpful for DSLR lenses that have very short throws, but also very helpful for some Cinema Lenses that have long throws. The expanded mapping on DSLR Lenses is designed to allow refined and precise focus pulls. The mapping process makes all lenses feel similar, allowing for a consistent feel throughout all lenses.

Wireless control of microRemote system up to 1 mile (1600m) line of sight

Adjustable Indicator Arm

Left/Right hand operation

3D Marking discs compatible with Flares for use in the dark

A dual adjustable hard stop for precision pulls

Powered by 2 AA batteries

Camera Run/Stop triggering

Reversible direction

Lanyard loop for resting around neck

1/4"-20 thread for building into a rig

Related Questions and Answers

Q: 1. Is this 3pin lemo connector compatiple with the 3 pin lemo port on the Steadicam Zephyr which is an 12-24v EGG-0B-0303?

A: Hi JB - thanks for asking. This cable is designed for the powerPack to power barrel connector devices such as compatible smallHD monitors.I think we saw a similar question coming from you earlier, so if you are looking for a custom cable you might drop us a line directly and see if we can solve your problem.

Q: 2. Is that new setup with Atlas motor Redrock Micro Atlas Smart Motor Single Channel Focus Control With Wireless Hand Controller B&H # RE621550001here is the link to it https://a href= http://www.bhphotovideo.com/c/product/1338835-REG/redrock_micro_62_155_0001_atlas_smart_motor_single.html target= _blank www.bhphotovideo.com/c/product/1338835-REG/redrock_micro_62_155_0001_atlas_smart_motor_single.html/a better than regular torque motor from redrock micro?We are now looking for the wireless follow focus system to use with our Ronin M gimbal; and a7sII camera and this Atlas motors with no base station looks nice but are they better than a torque one?Are Atlas motors are more professional or&?And other question is how many atlas motors can the Redrock Micro microRemote Handheld Wireless Focus Controller work with?

A: Hi Iaroslav thanks for your questionsthe Atlas motor has several advantages over the Torque motor:1. it has 300% more torque and 200% more resolution2. it has the brain integrated into the motor, so there is no separate basestation3. it has many other advantages as a smart motor, including integrated radio, sbus (for drone and gimbal communication), wifi, app for configuration, daisy chain to support multiple channels, etc. - you can learn more about it on our website a href= http://shop.redrockmicro.com target= _blank shop.redrockmicro.com/aThe microRemote hand unit is a single channel hand unit. The atlas motors can be daisy-chained for FIZ (focus, iris, zoom)if you are looking for a 3 channel gimbal style control consider the Navigator 7-in-1 Command Module which has additional benefits to control the Ronin-M gimbal from the joystick as well, AND you can run it as solo operator fingerwheel style, or wireless FIZhope that helps

Q: 3. Will these cables work with the Ronin M?

A: Hi Stephanie - thanks for asking. Yes the flexCable wireless kit works for all Ronins including Ronin M

Q: 4. Will the finger controller work with the PD Movie? a href= http://www.bhphotovideo.com/c/product/1048138-REG/ikan_pd1_pd_movie_remote_air.html target= _blank http://www.bhphotovideo.com/c/product/1048138-REG/ikan_pd1_pd_movie_remote_air.html/a

A: The Redrock microRemote finger controller is not listed by ikan as a possible acessory.

Q: 5. Will this power the Red Komodo and Cine 7?

A: The Red Komodo and the SmallHD Cine 7 both have a 2-pin LEMO power connector, so in theory it should work. However with out testing I cannot confirm. This cable is described to power an optional Redrock microRemote.

Q: 6. I have the thumb wheel set. Will this controller only set up match with the unit I have now? Or do I need to purchase something else as well?

A: Hi LucasThanks for your question. If you have a microRemote fingerwheel system including basestation and motor, then you only need to purchase this hand unit and it will work correctly to provide wireless remote focus. You just need to ensure the basestation and the hand unit are on the same channel. if you have any additional questions on how to use please contact us at support@redrockmicro.comthanks!

Q: 7. Can this motor be assigned and controlled by the movi controller?

A: According to Redrock Micro yes it can. The SLS Lens Motor is compatible with the Freefly’s MoVI Controller.

Q: 8. are both connectors Pin-1 +VDC? Thank you.

A: If I understand your question, you want Pin-1 to be +VDC. The answer then would come from what power source it is connected to. If that is Pin-1 +VDC, this would be as well.

Q: 9. can i use this on a devin graham glidecam and a jib? also, can you reccomend the kind of cables i need if i were to use this on a 8ft jib. thanks

A: Hi Divine - yes, it should work fine! we don't have direct experience with the glidecam, but many customers use it with steadicam, which works the same. Remember you'll need a small lightweight battery, check out our new lp-e6 battery adapter, which is about to be released (you will want to ask for part number 2-178-0001)this bundle is great for that. For a jib you'll want a longer cable, which we can make to size, but you will need to contact us at redrock micro direct for that cable. Everything else is available here.

Q: 10. I see that the basestation is wireless ready , does that mean it will connect and work with the handheld wireless remote?

A: Hi Anthony - yes that is correct. just add this hand unit (you can purchase it later) and its ready for wireless:a href= http://www.bhphotovideo.com/c/product/1014379-REG/redrock_micro_3_114_0001_microremote_handheld_wireless_focus.html target= _blank http://www.bhphotovideo.com/c/product/1014379-REG/redrock_micro_3_114_0001_microremote_handheld_wireless_focus.html/aplease note the picture of the hand unit is outdated - the new version is slimmer and smaller