You are using an outdated browser. For a faster, safer browsing experience, upgrade for free today.
Phones: 800
$ USD
  • Your shopping cart is empty!

Redrock Micro Mini Control Port Run/stop Cable 2.5mm Lanc

Redrock Micro Mini Control Port Run/stop Cable 2.5mm Lanc
  • Product Code: eq45602
  • Availability: In Stock

$435.00 $526.35

This Redrock Micro Mini Control Port Run/Stop Cable 2.5mm LANCfrom Redrock Micro Mini Control Port Run/Stop Cable 2.5mm LANCconnects the Redrock Navigator Atlas Motor to cameras with a standard 2.5mm LANC control port.

Connects Redrock Navigator Atlas Motor to 2.5mm LANC Port

Parameters
Length12" (30.5 cm)

flexCables are 35% lighter than most standard cables thanks in large part to the cable sheathing that's ultra-lightweight (yet still provides the required protection).

flexCables have a 200% greater flexibility than most standard cables, allowing for less drag and easier cable wrangling. These cables can be wrapped, twisted, and bent to keep your rig tight without damaging or crimping the cable.

flexCables are 20% thinner than most standard cables. You can easily install them where you need to and secure them with little effort.

Related Questions and Answers

Q: 1. Does this work with the Teradek RT Latitude MDR-M (2 channel motor driver receiver) and Sony FX6 camera?

A: Yes, the Teradek RT Latitude MDR LANC Run/Stop Cable (16") will support the Sony FX6 Cinema camera.

Q: 2. Would this work on a canon c300 mark iii?

A: The Teradek RT Latitude MDR LANC Run/Stop Cable (16") (B&H# TE111376) will connect to the 2.5mm LANC port of the Canon EOS C300 Mark III Digital Cinema Camera (EF Lens Mount) (B&H# CAC3003EF) for control using a Teradek RT MDR receiver such as the Teradek RT Latitude MDR-M Receiver (1-2 Axis) (B&H# TE150008).

Q: 3. Does the Lanc cable also work with the Sony FX9?

A: Yes, this LANC cable is compatible with the Sony FX9.

Q: 4. Will this cable work between a Atomos Shogun and a Redrock micro wireless base station?

A: Hi Kevin - This is specific to the one man crew, so the better starting point for the remote and shogun is the other cable you inquired about. see that answer

Q: 5. Would this work for the Sony fx3

A: Tilta does not list Tilta Run/Stop Cable for Tiltaing Side Focus Handle (LANC) as compatible with the Sony FX3.

Q: 6. Does this work with the Blackmagic Cinema Camera 2,5 K Ef lanc port?

A: No.

Q: 7. Does this cable also work with the Remote Wireless Focus base station to be used with the wireless controller to trigger remotely from the hand unit?

A: Hi Luke - yes, for compatible Sony cameras that have a LANC port it's the same cable. If you have more compatibility questions you can drop us a line at sales@a href= http://redrockmicro.com target= _blank redrockmicro.com/aHope that helps

Q: 8. Does this work with the Atomos Shogun?

A: Hi Kevin - i see you've asked this in a couple different places. I recommend you contact us directly, as this cable has been tested only with the camera lanc. it's possible, but we'd have to test it. Thanks

Q: 9. is this the cable to connect the redrock micro navigator to the movi?

A: The Redrock Micro micro Control Port Cable to MoVI Pro Control Port (36") Connects Redrock Satellite Universal Gimbal Controller to Freefly MoVI Pro.

Q: 10. Will this cable work with the Fx9

A: Yes, this is compatible with the FX9.

18/09/2024

[12" (30.5 cm)] Must have if you are a Nucleus-M and RED Komodo owner. It is compatible with the RED Outrigger handle and grants the Outrigger smart pins a pass-through connection. This is good for CamOps to trigger record via handle or for 1st ACs to trigger record via the Nucleus-M remote focus wheel depending what your shooting setup is (handheld, dolly, gimbal, steadicam, etc). There is also no latency on the trigger record in my experience unlike older RED camera models; my Nucleus-M trigger recording is instantaneous.

5
17/09/2024

[12" (30.5 cm)] I use this with the Nucleus M handles and a Blackmagic Ursa G2 shoulder rig. The cable is a little long but it can be secured with bongo ties, velcro, or tape.
Just connect it to a Nucleus motor, wirelessly pair the handles or FIZ with the motor(s), and plug the LANC end into the camera body. Now your Nucleus M record buttons work like a charm wirelessly.

5
08/09/2024

[12" (30.5 cm)] Works perfect for Fx6. Recently had a shoot with three Fx6s rigged in the ceiling and chose this method to control run/stop on the day. Had three separate systems and all worked perfectly.

5
05/08/2024

[12" (30.5 cm)] This cable works - but it's too small to plug into the grip input on side of camera - you have to find the smaller input covered with a black plastic cover, below the BNC connectors. The input is right below the timecode BNC connector. Enjoy remote stop-start with the Nucleus-M!

5
26/07/2024

[12" (30.5 cm)] Works flawlessly with the Z-Cam E2 F6 for Run/Stop with the Tilta M series controllers. Tried another cable (I think for the GH5 that looks similar but is incorrect).

5
21/04/2024

[12" (30.5 cm)] Easy to use and does the job

5
07/04/2024

[12" (30.5 cm)] Picked this up to get the Tilta m handle working with the ursa g2. Works a treat. No issues what so ever and great length. Connects extremely well, definitely won’t slip or accidentally pull out

5

Write a review

Note: HTML is not translated!
    Bad           Good
Captcha

Top Bestselling Products

Products You May Like

Dw Drums 5000pk5 Drum Hardware Pack

$3,839.97 $4,761.56

Gibraltar 9608hm 16" Hydraulic Drum Throne

$689.97 $869.36

Overboard Pro-sports Waterproof Camera Bag

$149.85 $202.30

Manfrotto Mt190cxpro4 Carbon Fiber Tripod Kit

$1,829.85 $2,214.12

Ceiling Mounted Projector Screen

$19,194.00 $28,407.12

Elation Artiste Picasso Moving Head Fixture Black

$25,500.00 $34,935.00

Samsung Qm32c 32" Full Hd Monitor

$1,980.00 $2,871.00