The GyroVu Heavy-Duty Articulated Arm 7" Shoe Mount7" GyroVu Heavy-Duty Articulated Arm 7" Shoe Mountallows you to attach a monitor or other accessory directly to your camera's hot shoe or to a camera cage that has a shoe mount. The maximum supported load capacity of 12 lb is best attached to a cage since that's too much weight for your camera's hot shoe, but lighter devices and accessories can safely be mounted on your camera. This arm comes with a shoe mount adapter secured on one end, and this adapter can be removed to provide you with a 1/4"-20 post on each end, allowing for alternate mounting options. Fully extended, the arm measures 7". A wingnut in the center tightens all three points of articulation at the same time.

12 lb Load Capacity    1/4"-20 Post on Each End    Removable Shoe Mount Secured on One End

Related Questions and Answers

Q: 1. Can you remove this arm from the clamp, if so does it have a standard tripod 1/4 20 thread?

A: The clamp is locked onto the arm with Loctite. It is not meant to be detached. If you contact GyroVu directly, they can assemble one for you without the Loctite.

Q: 2. would this 11" arm be good for mounting a Godox M1 (B&H # GOM1) to something like an oben Table top tripod (BH #OBTT100)? I don't want to use something ridiculously large like a full blown cstand/lightstand/camera tripod to mount a 1/2 lb godox M1 unit, but would like more angle and height versatility, that presumably a 11" arm would give. But not sure if it's a wise way to get there, if the 11" arm would be too top heavy for the oben tabletop tripod/tip over, etc. I would be looking to use it in vehicle interiors and behind subjects of a greenscreen to create separation. I find having the tabletop pod on the floor or on a carseat isnt verstatile enough (light looks too underlit and unnatural) and don't have places to clamp the godox m1 inside a car without damaging cars i don't own, etc. And similarly, the angle of the light for backlighting a subject to create separation w a greenscreen isn't high off the ground enough to get an effective wrap around a seated subject, if am just using the tripod on the floor. Plus it would be great to be able to angle the light to fine tune a greenscreen key, etc.

A: The Manfrotto 209 Tabletop Tripod (BH #MA209), would be more suitable to support the Gyrovu Heavy-Duty Articulated Arm (11-), as it has a much higher load capacity. You may also want to consider a small sandbag for further reaches of the arm with the Godox M1 light. https://bhpho.to/3CWx6en

Q: 3. How much weight can this support at full extension?

A: GyroVu does not publish the payload of the GyroVu Heavy-Duty Articulated Arm with Dual Jaw Clamps (11").

Q: 4. Can you attach this to a carbon fiber leg on a tripod to use in conjunction with your video camera?

A: The GyroVu Heavy-Duty Dual 11" Articulated Arms with Adjustable Clamp could be clamped to the leg of a tripod if the diameter was between .5-1.5".

Q: 5. What is the maximum length of this fully extended and the individual length of each arm?

A: Fully extended it is about a 6 length. The two arms are about 3 .

Q: 6. What is the load capacity of this item?

A: The GyroVu Heavy-Duty Dual 11" Articulated Arms with Adjustable Clamp does not state the load. It is meant for putting light weight devices. We would suggest that 2-3 lbs is the limit.

Q: 7. Will this work on a crane weight bar?

A: Yes 100 %. The following unit offers a clamping range of 0.5 to 1.5"

Q: 8. How long is the whole thing? Is there a longer one? It says 'dual' arm, but looks like there are FOUR segments?

A: There are two articulated arms connected together. Overall length of articulated part is 19.5". Overall length with adjustable clamp - 22". Sincerely, GyroVu Team.

Q: 9. could this be used to mount a dslr to a desk?

A: Yes, providing that your desktop is not thicker than 2.5". Sincerely, GyroVu Team

Q: 10. What is the max capacity that this arm can hold? Would a EOS R with a 35 mm Sigma lens be too heavy?

A: A load capacity for this arm is not listed. However it is really designed for accessories only and we do not recommend it with a camera the size of the EOS R. The Impact 3 Section Double Articulated Arm with Camera Bracket, BH #IMBHE119K, and a Impact Clamp would be a much better choice, BH #IMCC106R. https://bhpho.to/3oYTlGM https://bhpho.to/2Y8DWbb