The Kupo 5/8" Super Grip Finger - Durable Toolfrom Kupo 5/8" Super Grip Finger - Durable Tooladds a swiveling 5/8" baby pin on an integrated ball head to camera and lighting rigs. The Finger mounts on stands and other points with its dual-function spigot, which may be configured as a 5/8" receiver or a 1 1/8" junior pin.

Chrome-Plated Construction    Ball Head with 5/8" Baby Pin    360° Rotation | 115° Tilt    Ratcheting Locking Handle

The Super Grip Finger from Kupo adds a swiveling 5/8" baby pin on an integrated ball head to camera and lighting rigs. The Finger mounts on stands and other points with its dual-function spigot, which may be configured as a 5/8" receiver or a 1 1/8" junior pin.

Kupo offers its Super Grip line of ball head actuated grip equipment to incorporate an extra degree of precision adjustment to your various camera, lighting, and other production rigs. The Super Grip Finger provides a sturdy steel 5/8" baby pin with 360° of rotation and 115° of tilt to carefully dial in the placement of payloads. With enough strength to support up to 22 lb, the Finger can effectively act as a freely configurable upgrade to the top mounting point of C-stands. For setups that require heavier-duty support, the lockdown knob on the 5/8" receiver can be removed to mount the Super Grip Finger in 1 1/8" junior ports, like those on combo stands or C-stand turtle bases.

Related Questions and Answers

Q: 1. I have a luxli fiddle light. I think think the scre is 3/16. Is there a way to adjust this ballhead for that?

A: The Luxli Fiddel has a 1/4 20 female thread Impact Small 3/8"-16 Female Threaded Adapter to 1/4"-20 Male Threaded Post will let you. This will let you use the Kupo Super grip ball head.

Q: 2. What is the max weight this can hold?

A: The Kupo 5/8" Swivel Super Grip Finger with Ratcheted Handle can support up to 22 lbs.

Q: 3. Will this grip arm support work with other C-stands with grip arms, i.e. A Matthews Hollywood C-Stand?

A: It can work with any C-stand but you will also need a Kupo 3 way clamp, this fits the C-stand. The grip arm can't be greater than 16mm (I had to look that up on the Kupo site). I bought this when I tried to mount a Westcott Apollo Orb, and pair of Cactus RF60 Flashes with battery packs and it was able to keep it in position. Without it I couldn't keep it upright.

Q: 4. Would two of these be secure enough to hold a slider on stands? Thinking they might allow different stand heights, for slider to be inclined. Regular Kupo ball head adapters would need to both be level. Not sure if these would cause instability or want to flop over to one side or other because of weight.

A: Yes. But would suggest the following for a better experience. Just add a washer with a 2 inch diameter Impact Rapid Baby to 1/4"-20 Male Threaded Adapter BH #IMCA101 • MFR #CA-101 https://bhpho.to/3DMiFXY

Q: 5. How tall is this?

A: The Kupo Super Grip Finger with Round Camera Plate is 6.02 inches tall.

Q: 6. Will this scratch bottom of camera?

A: Anytime you are attaching a metal plate to a camera body you can run the risk of scratching especially when set screws are involved such as in the Kupo Super Grip Finger with Round Camera Plate.

Q: 7. Can the 1/4" thread be replaced with a 3/8" thread? I prefer to not use an adapter.

A: Unfortunately, we do not have a super grip finger option that has a built-in 3/8"-16 male screw. As an alternative, I would recommend purchasing the Impact Heavy-Duty Swivel Pin, B&H # IMSRP118, and the Kupo Baby Ball Head Adapter, B&H # KUKG014212, as an alternative for your usage needs.

Q: 8. How far does the hex receiver stick out? We need it to extend a certain distance from the beam we are clamping onto.

A: It is 2.5" from the notch in the clamp to the opening of the receiver.

Q: 9. What size is the ball? Is this like a 1” Ram Mount?

A: The ball is 26mm.

Q: 10. Where is the size measured from? The maximum jaw gap, or the length of the entire clamp?

A: The bolt is 4" the overall length is longer at 8.75".