This Acebil 150mm Ball Tripod Head with Dual Handlesfrom Acebil consists of a 150mm fluid ball head with dual telescoping handles and an illuminated bubble level. The head supports a maximum load of 132 lb.

The fluid head features a two-step counterbalance system and supports up to 99 lb of counterbalance weight. The pan and tilt systems each offer eight steps of drag with continuous motion, and its tilt angle is +90°/-75°.

The sliding, side-loading quick release plate offers two 3/8"-16 mounting screws, and spare 1/4"-20 and 3/8"-16 mounting screws are included. The head is also compatible with ARRI and OConnor mounting plates. The built-in LED-illuminated bubble level allows you to balance your camera in low light. Dual telescoping pan handles connect to the head on either side via rosette mounts.

Tripod Fluid Ball Head    150mm Ball Size    Side-Loading Quick Release Plate    LED-Illuminated Bubble Level    132 lb Load Capacity    Dual Telescoping Pan Handles    Double 3/8"-16 Mounting Screws

150mm fluid ball head with dual telescoping pan handles and quick release plate

Load capacity of 132 lb

Counterbalance system supports up to 99 lb of counterbalance weight

LED-illuminated bubble level to assist balancing in low light

Plate includes two 3/8"-16 camera mounting plate screws; spare 3/8"-16 and 1/4"-20 screws are included

Compatible with ARRI and OConnor mounting plates

Related Questions and Answers

Q: 1. Tell me, is this truly an actual fluid head? Thank you in advance.

A: We spoke with Acebil and they say yes, this is a fluid head. In fact, the entire Acebil line is fluid head except for the entry level consumer models.

Q: 2. How do I replace the rubber feet on my VEO 3T+234CB to spike feet?

A: They should pull off and or twist off. We do not have this on display to check.

Q: 3. Is it arca-swiss compatible with the peak designs capture clip v-3 plate and does the clamp have a lock pin?

A: Generally arca swiss standard parts are compatible. However, this combination is unknown so we cannot guarantee the compatibility. There is a quick release safety lock.

Q: 4. Is this thing sufficiently stable to support a DJI Osmo Pocket 3 in a raised position for use as a webcam?

A: Yes, the PGYTECH CapLock MantisPod Z Tripod with Ball-Head could support the DJI Osmo Pocket 3 in a raised position. It is recommended to have the camera centered over the tripod for greatest stability.

Q: 5. Is that 4 pound listed weight includes the ball head or is it just for the tripod legs?

A: The four pound weight is just for the legs.

Q: 6. Will this work on a 100mm Miller tripod?

A: Yes the Acebil CH4 Fluid Head (100mm Ball) will fit on other 100mm tripods.

Q: 7. I have a Panasonic HC-X920 camcorder. I was wondering if this zoom control handle can connect to the camera? All I see for 2.5 stereo jack connections are headphones and an external microphone. Will this tripod connect to this camera? If so, where does it connect? Thank you.

A: The tripod zoom handle has a cable with a jack at the end to plug into your camcorder.The Panasonic called out does not have this feature Remote input-port for this jack.Example is to look at a camera that has this remote-port, like the Canon G30 camcorder.I do make use of this handle in capturing soccer games where a lot of panning left-right movement occur.This is near a professional tripod, get a camcorder that mates with it...the handle works great when capturing lots of subjects in motion... good luck.

Q: 8. What is the base diameter of this ball head?

A: We measured the diameter as 29.3mm / 1.15".

Q: 9. What is the weight capasity?

A: This supports up to 15kg - 33lb.

Q: 10. will this work on my canon XA20 video camera?

A: This should work well with the XA20 plus the zoom control is of the LANC type so it interface correctly with the camcorder and you will have smooth zooms.