The pair of white Pyle Pro 10" In-Wall/Ceiling 250W Stereo Speakers Whitefrom Pyle Pro 10" In-Wall/Ceiling 250W Stereo Speakers Whitefeatures two-way speakers that deliver stereo sound to any room in your home or office. The system comes with changeable round and square stain-resistant grille covers and cut-out templates for easy and quick installation. They mount flush and achieve a clean look on walls or ceilings and provide a wide frequency response of 35 Hz to 20 kHz.

These speakers feature environmentally friendly ABS construction. The woofer material is made of polypropylene material with rubber edges and the tweeter is made of 1/2" high compliance polymer material. Additionally, the built-in electronic crossover network helps deliver 2-way, wide-stereo audio for any and every day musical applications.

For In-Wall, In-Ceiling System    250W Peak Power    35 Hz to 20 kHz Frequency Response    2 x 10" Speakers    1/2" High Compliance Polymer Tweeter    Polypropylene Cone with Rubber Edge    Mounts Flush on Walls or Ceilings    Built-In Electronic Crossover Network    Includes Round and Square Grilles    Cut-Out Template for Easy Installation

Related Questions and Answers

Q: 1. Are these speakers switchable between 4 and 8 ohms?

A: Two of the speakers with a stereo amplifier will be 8 ohms. If you add another pair of speakers, they would run at 4 ohms and require twice the power.

Q: 2. The specs on give the box dimensions not the unit dimensions. How tall is this?

A: The unit's dimension is (L x W x H): 19.09'' x 9.84'' x 3.54'' -inches.

Q: 3. Are these speakers compatible with my Pyle Amp. PPA66BT

A: If used as passive speakers, without connecting the included 12V power supply, the pair of Pyle Pro PDICBT87 8.0" Bluetooth Ceiling/Wall Speakers can be used with the Pyle Pro PTA66BT Bluetooth Audio Power Amplifier. When used as passive speakers, the internal Bluetooth feature on the speakers will not be active, but the Bluetooth feature on the amplifier allows Bluetooth audio to be streamed through the speakers.

Q: 4. Can SVS Prime elevation speaker mount be used with this?

A: The Pyle Pro Swivel/Adjustable Wall/Ceiling Speaker Mounts will support the weight of the SVS Prime Elevation Speakers, but we are not able to confirm whether the holes on the mounting bracket that is included with the SVS speakers will line up properly with the holes on the plate for the Pyle Pro Speaker Mounts.

Q: 5. Most wall volume controls I see are for 70v speaker systems. Is this safe to use with a standard power amp and PA speakers?

A: Yes, it is safe to use.

Q: 6. What should I have the gain at?

A: I have mine running a eurolive vp 1220, pa speaker, with a xenyx 802 board. It is only using channel a and i have it set to +10. It is only in being used an averaged sized room so it doesn't need to go any higher than that. I would say as long as it is not clipping you should be OK. I would run whatever you will typically play through it, find where it starts to clip and then back it down to where it stops. That would be a good max setting in my opinion. Also, check the user manual for your speakers for limits. You definitely don't want to blow them. I hope this helps.

Q: 7. Can you connect this to home audio receiver?

A: Not from the speaker outputs on the home audio receiver. Only if it has pre-outs available for that. A lot of models only have pre-outs for use with powered subwoofers.

Q: 8. I know Bose makes one for the sub, but would this pyle work with a Bose b1 subwoofer? The Bose amp is really expensive and I am looking for a cheaper alternative. Thanks in advance.

A: I use this amp as a talk-back and monitor amp driving 2 JBL P60 speakers and it has plenty of power. I don't know if it would drive a sub-woofer. It all depends on the size and wattage of the Bose I guess. If it's over 250W it might not do the job.

Q: 9. It works with 4 and 8 ohm. What about 6 ohm?

A: The Pyle Pro PTA1000 is able to run at either 4 ohms or 8 ohms, but not 6 ohms.

Q: 10. I have a Klipsch KD-51M Bookshelf speakers & eventually will get a subwoofer. I want to connect to my computer. Will this work?

A: Yes, the Pyle Pro PTA1000 Professional Stereo Power Amplifier (250W/Channel @ 8 Ohms) (BH # PYPTA1000) will comfortably drive the Klipsch KD-51M bookshelf speakers. This amplifier will connect to your computer's analog audio output There is no subwoofer output on this amplifier.