This Lightweight Carbon Fiber Camera Slider 31.5" - Sevenoakis a lightweight easy-to-position slider which can support loads up to 15.4 pounds. The large carriage features a 3/8"-16 mounting screw that accommodates fluid heads of various sizes. It glides smoothly along the 18mm rails and features four guide rollers that ride along the outside of the rails. Two additional rollers press against the inside and allow you to adjust the tension of the carriage.

In addition to a 3/8"-16 mounting screw, there are two sets each of 1/4"-20 and 3/8"-16 threads on the carriage that are useful for mounting optional accessories. At the ends of the slider are angle-adjustable legs with height-adjustable rubber feet for leveling on uneven terrain. The carbon fiber slider rails are threaded and accept extension rails (not included), enabling you to extend the length of your slider. A padded carrying case is included for storage and transport.

Roller-Bearing Sliding System    4 x Track Rollers    2 x Tension Rollers    15.4 Pound Load Capacity    Lightweight 18mm Carbon Fiber Rails    Adjustable Legs for Leveling    Large Carriage with Accessory Threads    Available Extension Rails    Padded Carrying Case

• Durable and lightweight construction
• 18mm carbon fiber rails
• 15.4 lb load capacity
• Large camera carriage
• Four precision-sealed bearings on aluminum rollers guide the carriage along the rails
• Two roller bearings on a rotating platform on the underside of the carriage are used to provide adjustable tension to regulate the speed of the slider
• Mounted on the side of the carriage is a knob that tightens and holds the carriage in place
• 1/4"-20 and 3/8"-16 accessory mounting threads on carriage
• The carriage incorporates a bubble level
• Adjustable outrigger legs for leveling
• Center-mounting platform accepts 1/4"-20 and 3/8"-16 mounting studs, such as can be found on tripods or light stands
• The end blocks each feature 1/4"-20 and 3/8"-16 threaded mounting holes for accepting supports
• The integrated spring-loaded feet rotate on a rosette system so you can level the slider, tighten the legs, and not worry about the legs slipping

Related Questions and Answers

Q: 1. What's the maxium length of a timelapse you can do with this? I'd like to do a 3-4 days timelapse.

A: Like most any time lapse, you can do so for a long as you wish. The issue is more getting power to the device. You will need to research time lapse calculations to get a grasp of the process.

Q: 2. what's the difference between this and GVM GP-120QD model? Only IOS/Android APP support?

A: The most notable difference between the GVM Wireless Carbon Fiber Motorized Camera Slider (47-) (GVMSLIDER120) and the GVM GP-120QD (GVGP120QD) Motorized Carbon Fiber Video Slider (48") is that GVMSLIDER120 can be controlled via app and that GVGP120QD is controlled with a wired remote. GVMSLIDER120 is also listed at 47" and GVGP120QD at 48".

Q: 3. Is it difficult to get consistent steady flowing slides with this without it being motorized?

A: Operating a slider manually will take some practice to get down smoothly, but it is very possible with this slider.

Q: 4. How quiet is this slider?

A: The GVM Wireless Carbon Fiber Motorized Camera Slider motor can be heard at higher speeds and in time lapse mode there is a clicking sound.

Q: 5. Will the slider trigger my Nikon D850 for Timelapse control? I want them synchronized.

A: Please add the following shutter cable to your purchase to control the Nikon D850 when using the GVM Wireless Carbon Fiber Motorized Camera Slider. Vello 2.5mm Remote Shutter Release Cable II for Cameras with Nikon 10-Pin Connectors BH #VERCC2N125

Q: 6. What is the difference between this and the GVM GT-120WD?

A: The GVM Wireless Carbon Fiber Motorized Camera Slider (47") uses on NP-F for power and can be controlled via a cellphone or tablet with an app, while the GVM GT-120WD Wireless Bluetooth Carbon Fiber Motorized Camera Slider (47") uses two NP-Fs for power and is controlled via an included wireless controller.

Q: 7. Is the pan motorized or just the slider?

A: The slider is the only motorized part on the GVM Wireless Carbon Fiber Motorized Camera Slider.

Q: 8. What type of tripod would be best to use this? The one I have doesn’t have a head that will work.

A: A tripod without a head would need to have a 3/8 16 male screw to attach to the Axler 30" Lightweight Carbon Fiber Camera Slider. The Benro parts below would work as will the same model with a head. Benro 75mm Half Ball Adapter BH #BEBL75S Benro A373T Aluminum Video Tripod (75mm Bowl) BH #BEA373T or Benro A373F Aluminum Single-Tube Tripod with S8Pro Fluid Video Head BH #BEA373FBS8P

Q: 9. Can this be used manually, sliding by hand while tilting and panning the camera mounted in a fluid head?

A: Yes, you can move the camera manually across the slider, but it is not built for that and we can't recommend it, as the gears might prevent you from getting a smooth shot. For manual use, we'd recommend getting a non-motorized slider such as the Axler 30" Lightweight Carbon Fiber Camera Slider (BH #AXCSCF30LW • MFR #CS-CF-30LW).

Q: 10. Can you plug in the slider to wall power instead of using a battery?

A: The GVM Wireless Carbon Fiber Motorized Camera Slider (47") (B&H# GVMSLIDER120) can be powered using the Power2000 AC-F550 AC/DC Adapter with Sony L-Series Dummy Battery (B&H# POACF550) in place of the battery for it.