Compatible with 15mm LWS rod systems, this CAMVATE Adjustable Lens Support for 15mm Rodswith red knobs from CAMVATE Adjustable Lens Support for 15mm Rodsfits dual rods with a spacing of 2.4" center-to-center. The lens support helps carry the weight of lenses with a diameter of 50 to 140mm. There are two integrated rubber gaskets on the Y-shaped lens support for eliminating vibration and preventing scratches. You can adjust the height via a thumbscrew.

Fits Dual 15mm Rods, 2.4" Spacing    Compatible with 50-140mm Lens Diameter    Y-Shaped Lens Support    Height Adjustable via Thumbscrew    2 x Rubber Gaskets on Top    M5 & 1/4"-20 Threaded Holes    Aluminum Alloy Construction

Related Questions and Answers

Q: 1. Does the support lock on the 15mm rods? In other words, is the locking lever only for the post or does it lock both the post and the support to the rods simultaneously ?

A: The lever does the rods. The knob tightens the rod support.

Q: 2. I have zacuto recoil rig, V1 for my Sony fs5. Will this work suitable for my Nikon 70-200mm? Or is there another suitable lens support system that can screw into the foot of the lens?

A: It will work. You can always use the cradle. My issue is the shaft that goes vertically through the bridge is too long. If that is not an issue for you then this is a good deal.

Q: 3. What is the weight rating for this lens support? As it supports 50 to 200mm, with the links are only certain specific lens diameters within that supported?

A: Cavision does not have a listed weight support but the Adjustable Height Lens Support is a metal construction and strong. It supports lenses from 50 to 200mm in diameter.

Q: 4. Is the height fully adjustable like the smallrig? Or can you just choose between fixed position depending on the extension you choose?

A: Yes, the height is adjustable.

Q: 5. Does this match with a Canon RF 28-70mm f/2 L USM Lens paired with Tilta Tiltaing Lightweight Camera Support Kit for Canon C70?

A: As long as you place the Tilta 15mm LWS Rod Lens Support in a position that isn't on a focus or zoom gear, it will support as needed.

Q: 6. What's the minimum height you can achieve with the 1/4" adapter attached? I have 1cm clearance between the tip of the rod and the foot of the lens. Need to bolt it in as a v-mount still allows the lens to move.

A: Tilta has informed us that the minimum height is 2 inches on the Tilta 15mm LWS Rod Lens Support with the 1/4"-20 adapter.

Q: 7. will this fit fine onto my sony A6300 & A7iii?

A: You are able to screw this into the bottom of your Sony cameras.

Q: 8. what is the maximum height of the lens support rod? The Tilta universal support has a max of .875" and the Small Rig support is 22mm, (roughly .866")

A: According to 8Sinn the maximum height of this lens support is 80mm.

Q: 9. What is the minimum height achievable with the smallest 1/4" 20 post? I have a clearance of about 1.1-1.2cm.

A: Yes, The 8Sinn Universal Lens Support (15mm) will support your requirements. One of the extension posts in the Lens support kit is 1.8cm (18mm high) and it can be set to support the lens with a clearance of 1.1-1.2cm (which is 11 to12mm),

Q: 10. Would this fit in the Canon LH-E1 lens support (#CALHE1) if I remove the Y support part?

A: Yes, the Tilta 15mm LWS Rod Lens Support would fit in the bottom of the Canon LH-E1 Lens Holder after removing the Y lens adapter and using the included 3/8"-16 to 1/4"-20 adapter.