Whether you're live or in the studio, the ButtKicker Concert Low Frequency Audio Transduceris designed to help you play "in the pocket". Constructed specifically for stage and studio monitoring, the Concert Transducer houses a 3.75 lb magnetically suspended piston that responds to low frequencies to vibrate whatever its attached to, such as a plywood platform or a drummer's stool. Combined with an in-ear monitor, mixing and performing can be enhanced with the additional sensation of feeling the music.

Designed for Recording and Performing    Physically Feel Low Frequency Audio    3.75 lb Magnetically Suspended Piston    Responds to 5 to 200 Hz Signals    Mounts to Stage Platforms and Seating

Requires a power amplifier that supports frequencies below 20 Hz, and power output between 400 and 1500W. Mounting hardware and speaker wire are also required.

Vertical or Horizontal Mounting.

Thermal Switch - The ButtKicker Advance is set to shut down automatically if it gets too hot in order to prevent damage to the unit.

Related Questions and Answers

Q: 1. If I attach two wireless recievers into the tabs in the front pocket, will the antenna stick out? If it will, can I tuck the antenna into the main bag and zip the pocket closed?

A: Yes, in the scenario described the receiver antennae would stick out of the front pocket of the ORCA OR-268 Low-Profile Audio Mixer Bag for Zoom F6 when unzipped. Depending on the antenna length and flexibility, there is the possibility of zipping the front pouch closed and allocating the aerials into the main compartment.

Q: 2. Thanks, what amp is recommended to drive the 4 buttkicker advance? Is there a way to separately control the intensity of each unit?

A: An amp of 75-400 W. To control separate units, you would have to use separate amps or at least an amp with 2 channels, so adjustments could be made separately. ButtKicker BK4-4 Specs Frequency Response 5 to 200 Hz Nominal Impedance 4 Ohms (inductive) Power Handling Minimum: 75 W Maximum: 400 W

Q: 3. If I am to buy this, what other things I need to buy that would work with this? Thanks!

A: Additional Features & Requirements Requires a power amplifier that supports frequencies below 20 Hz, and power output between 75 to 400W. Mounting hardware and speaker wire are also required. Subwoofer Compatible - The ButtKicker Advance can be used with your existing subwoofer. If there is only one output, an optional Y-cable can be used. Thermal Switch - The ButtKicker Advance is set to shut down automatically if it gets too hot in order to prevent damage to the unit. Please note the accessories listed on this product page.

Q: 4. Will this work as a replacement for the handheld mike in the ATW-T801-T2 System? Our handheld mike grew legs!

A: This microphone /transmitter is compatible only with Audio-Technica System 9 receivers on 169 to 172 MHz VHF frequency band.

Q: 5. What are the two Velcro straps on the top edges supposed to be for? I've attached the tight little clips to the rails on the F6, but can't see what is the purpose of the 1 inch (2.5cm) wide by 7 inch (18cm) velcro strips.

A: The Velcro straps are included to secure a mixer inside the of the bag. The bag is designed to hold other mixers that are the same size as the Zoom F6 and would need to be secured from the top using the Velcro straps. You could use the straps for any other purposes since they are not needed to hold the F6.

Q: 6. will a AT829CW michrophone work with this?

A: Yes

Q: 7. would it be possible to mount the orca bag, with the zoom f6 inside + attached npf battery to a c stand? using something like a gyrovu clamp + some other attachment? Looking to avoid leaving the orca bag/f6 on the floor as a one man band operator, and would be extremely handy to have the orca bag and zoom f6 at eye level

A: It may be possible to mount the ORCA OR-268 Low-Profile Audio Mixer Bag for Zoom F6 to a stand with a clamp as described. A more preferable solution could be found in a shelf accessory such as the Gator Frameworks Small Microphone-Stand Accessory Shelf (9 x 9") (BH #GAWSHELF0909), which has a 10 pound weight capacity and is also available in a larger size: https://bhpho.to/3Gw1dc7

Q: 8. Is it possible to attach this to a belt?

A: There are no loops to attach to a belt. Only a shoulder strap.

Q: 9. What are the interior dimensions of the front pouch?

A: We do not have a measurement for the dimensions of the ORCA OR-268's front pocket.

Q: 10. do the speakers get glued to drywall?

A: This sound transducer is designed for mounting on drywall surfaces, and comes with a direct screw aluminum mounting base and an attached wiring harness with EuroStyle connector. This transducer can be installed in-wall and in-ceiling, and patent-pending acoustic in-wall mounting brackets are needed for installation (sold separately).