The Dante AVIO 1-Channel XLR Analog Output Adapterallows you to use the analog gear you already own with your Dante audio network. It provides audio engineers with a cost-effective solution for adapting analog power amplifiers, powered speakers, or analog compressors and equalizers, delivering the interoperability, performance, and scalability of Dante network connectivity.

Compact and built for the road, the AVIO is automatically discovered by the network and is ready to use when connected. It features one balanced, line-level output equipped with an XLR connector and delivers high-quality audio at up to 24-bit/96 kHz with configurable gain and attenuation, low total harmonic distortion, and a 20 Hz to 20 kHz frequency response.

The AVIO supports Dante Audio over IP and AES67 RTP transport formats, and is compatible with Dante Domain Manager (DDM).

Use Analog Gear with Dante Network    1 x XLR, Line-level Analog Output    Plug-and-Play Operation    Compact and Built for the Road    Audio Resolution up to 24-Bit / 96 kHz    Configurable Gain and Attenuation    Compatible with Dante Domain Manager    Dante Audio Over IP & AES67 RTP Formats

• Cost-effective solution for adapting analog gear to your Dante network
• Plug-and-play operation 
• Balanced, line-level single-channel analog output adapter
• Compact and built for the road with sonically welded polycarbonate enclosure
• Sample rates up to 96 kHz
• Wide dynamic range
• High signal-to-noise ratio
• Low total harmonic distortion
• Configurable gain and attenuation
• Dante Audio over IP and AES67 RTP transport formats
• Power over Ethernet (PoE) support
• Compatible with Dante Domain Manager (DDM)

• Send audio to analog power amplifiers and powered speakers over a Dante audio network
• Patch DSPs, analog compressors and equalizers into a Dante system using a combination of Dante AVIO input and output adapters
• Create easy drop points for connecting overflow areas to a Dante network
• Connect non-networked hearing aid loop amplifiers to your Dante audio network

Related Questions and Answers

Q: 1. Will the AVIO 1 Input adapter except a 25 volt or 70 volt audio signal or does it need to be adapted to a line level first?

A: The Audinate Dante AVIO 1-Channel Analog Input Adapter for Dante Audio Network is intended for a balanced, line-level input signal.

Q: 2. Can the input version and output version of these units be used together as a standalone 2 channel dante system?

A: Yes you can, however you would need a switch as well.

Q: 3. Can the input / output version of these units be used together?

A: It would be helpful to have more details about the application you would be using this for as well as what you are connecting to and from. Please email us at audio@bhphotovideo.com with the information so we can best assist you..

Q: 4. Will the AVOI 1 Input adapter accept a 25 or 70 volt signal direct from a power amp or do you need to adapt it to a line level ?

A: The Audinate Dante AVIO 1-Channel Analog Input Adapter is used to connect a line level output signal from an analog device to a Dante audio network.

Q: 5. 2 inputs x 1 output. Does this mean I will only have 1 mono signal output?

A: The Dante AVIO Bluetooth Adapter always outputs two Dante channels. It supports one A2DP connection for music and HFP connections for calls. For A2DP profile music, the output is stereo and uses both left and right channels. For HFP profile calls, the output is dual-mono, with the same content on both left and right channels.

Q: 6. How to find this MAC address

A: The address of Dante devices such as the Audinate Dante AVIO 1-Channel XLR Analog Output Adapter for Dante Audio Network can many times be found on the physical unit itself. Alternatively, the device and address could also be located in the Dane Controller. The article linked here provides further insight: https://bit.ly/3hr4rSI

Q: 7. Will this adapter work with analog microphones and supply phantom?

A: No, the Audinate Dante AVIO 2-Channel Analog Input Adapter for Dante Audio Network will not accept a microphone signal or supply phantom power. This adapter will integrate analog line level signals into a Dante Audio Network.

Q: 8. What speakers can I connect to this and with what connector?

A: Powered monitors via a 3-pin female XLR connector.

Q: 9. Would this be the correct adapter to add an intercom system to my Dante Network? I'm looking to integrate a Clear-Comm FSII Base

A: No, the Audinate Dante AVIO 2-Channel XLR Analog Output Adapter for Dante Audio Network would not be the correct adapter to use with your Clear-Comm FSII Base; it would work for output only. Instead, I would recommend using one B&H # AUADPDAOAU1 for output from the Dante system to the program input on your intercom base, and one B&H # AUADPDAIAU1 for the stage announce output of your intercom base into the Dante network.

Q: 10. if I have an output and input adapter do I still need some type of Dante management software for them to work or does it just work automatically?

A: The Audinate Dante AVIO 1-Channel XLR Analog Input and Output Adapters for Dante Audio Network provide plug and play operation. A common PoE (Power over Ethernet) switch is required and the Dante Avio adapters are compatible with Dante Domain Manager software for IT-level security and management. Dante Controller software can be used on any connected Windows or Mac computer in order to adjust audio controls for the Dante AVIO adapters. The software options can be used if desired, but it is not required for the adapters to function.