Designed for commercial use, the Dahua DH-PFS3006-4ET-60 4-Port PoE+ Ethernet Switchfrom Dahua DH-PFS3006-4ET-60 4-Port PoE+ Ethernet Switchcomes with a total PoE power budget of up to 60W so you can plug PoE-compliant devices into any of the four Gigabit PoE+ ports. Alongside the four Fast Ethernet ports, you will find dual Fast Ethernet uplink ports to connect various network components directly to the switch. Once configured, the Dahua switch resides on Layer 2 of the network and supports a variety of network standards including 802.3, 802.3u, 802.3X, 802.3af, and 802.3at. Furthermore, this PoE switch is capable of transmitting power and data at distances of up to 820' to give you maximum flexibility when configuring your devices.

4 x Fast Ethernet PoE+ Ports    2 x Fast Ethernet Uplink Ports    1.8 Gb/s Switching Capacity    890 Kpps Packet Forwarding Rate    768 Kb Packet Memory Buffer    2K MAC Address Table Size    Flow Control Enabled by Default    60W PoE Power Budget    802.3at/af PoE Standards Compliant

• Layer 2 commercial switch

• Long-distance PoE (LD PoE) transmits power and data up to 820'

• Conforms to IEEE 802.3, IEEE 802.3u and IEEE 802.3X

• Conforms to IEEE 802.3af and IEEE 803.3at

• Supports hi-PoE (60W)

• MAC auto-learning and Aging; 2K MAC address capacity

• MDI/MDIX self-adaptation

• Metal enclosure

Related Questions and Answers

Q: 1. What is the forwarding rate for this switch?

A: Netgear does not specify this. But here is the data sheet for some other helpful information on this switch. https://www.netgear.com/media/GS108LP_GS108PP_GS116LP_GS116PP_DS_tcm148-68424.pdf

Q: 2. Can two of these switches be daisy chained and if so does it have AutoMdix capability or is a Patch style cable required?

A: The Netgear GS308EP 8-Port Gigabit PoE+ Compliant Managed Switch features auto-MDI/MDIX.

Q: 3. If I have a 24vdc Access point that takes .5 amps will this damage it? I see that it is 1.2amps

A: The amount of current in the scenario you present will not be as critical as the wattage required by the end device. The rating indicates the maximum amperage that can be provided. The primary factor in PoE is wattage.

Q: 4. Is it L2/L3 switch or just L2?

A: Yes, this Netgear GS308EP 8-Port Gigabit PoE+ Compliant Managed Switch is possible to work as L3. https://bit.ly/4aVmhYv

Q: 5. How does the Nano switch get power?

A: The Ubiquiti Networks NanoSwitch Outdoor 4-Port PoE Passthrough Switch would require a POE in to get the original source of power.

Q: 6. What are the temperature ranges for this device?

A: The operating temperature for this switch is 32 to 104°F / 0 to 40°C.

Q: 7. What is the total power available for PoE?

A: It doesn't provide PoE

Q: 8. Is this v2 version?

A: Unfortunately, we are unable to check the serial, batch, firmware or OS version of the Netgear ProSafe Plus 5-Port Gigabit Ethernet Switch BH #NEGS105E200.

Q: 9. Is it possible to plug a non-POE unit into this switch without damaging the non-POE device?

A: Yes. It is possible to plug a non-POE unit into the Netgear 8-Port Gigabit Ethernet PoE+ Unmanaged Switch.

Q: 10. I use one of these for our (AVB) audio network, but would it work for an NDI network (Using a separate network)? I'm looking for a POE switch with an ethercon connector for a portable setup (running only 2 Cat6 (or6a) ethernet cables from FOH to stage), one for NDI video and one for AVB audio. (AVB video not an option)

A: The PreSonus SW5E 5-Port AVB Switch with PoE appears to only offer compatibility with AVB products and does not specify compatibility for use with other network protocols such as NDI.