The beige, 110mm DPA Microphones d:fine Core 4266 Omnidirectional Miniature Mic Boomfrom DPA Microphones d:fine Core 4266 Omnidirectional Miniature Mic Boomis a replacement microphone boom for the d:fine headset (sold separately). Designed for theater and broadcast applications, the Core 4266 amplifier technology delivers a 14 dB increase in both THD (total harmonic distortion) and dynamic range than the Legacy 4266 model. This miniature mic boom requires an optional cable and headset.

Replacement Mic Boom for d:fine Headsets    Omnidirectional Polar Pattern    For Stage and Television    Core Amplifier Increases Performance    14 dB Increase in THD and Dynamic Range    20 Hz to 20 kHz Frequency Range    Requires Cable and Headset

Pristine audio quality

Lightweight and flexible

Minimal visual impact

Resistant to humidity

Flexible adapter system fits most professional wireless systems

Related Questions and Answers

Q: 1. does this work with the AT 2035

A: This studio arm would work with the Audio-Technica AT2035 cardioid condenser microphone. Simply attach the AT8458 shock mount that comes with the microphone to the 5/8-inch threaded end of the arm.

Q: 2. I am reaching out regarding this boom arm. Does this product fit the SM6 shock mount?

A: Yes. This will fit any standard mic clip or shock mount.

Q: 3. Does it work with AT2020USB+?

A: Yes, fully compatible.

Q: 4. Would this work with Rode VideoMic NTG Hybrid Analog/USB Camera-Mount Shotgun Microphone, or will it want to jump to the sky?

A: Yes it will.

Q: 5. Is the 4-pin Hirose connector the same as a Sony 4-pin connector, for example on the DWT-B01 transmitter?

A: Yes, this mic is compatible with that Sony transmitter. It's pretty decent, too!

Q: 6. Can you flip one of the screws so that one screws "up" and the other screws "down" or are they both locked in that position?

A: Yes, the threaded bushings on the bottom of the Gator Frameworks Mic Mount Bar can be removed with a flathead screwdriver so you can position the screws as needed.

Q: 7. I lost my foam windscreen for this mic, any recommendation for replacements?

A: Please review the following item. Auray WSF-2029 Foam Windscreen for Shotgun Microphones - (29cm) BH #AUWSF2029 • MFR #WSF-2029 https://bhpho.to/3GGDIgJ

Q: 8. Does anyone use a pop filter with this arm? If so how do you attach?

A: You can clamp it onto the boom arm. So the pop screen will move with the mic. This is a good one made by K&M. B&H # KM23956B you can find it on our website.

Q: 9. Will this work with plug-in power from these devices: Sony PCM-M10, Zoom H1N, EOS-M3, Canon 5D3 ?

A: The MCSM-4 can operate on 1.5 to 10 volts and will be compatible with most devices that provide plug in power.

Q: 10. Can this mic be rigged on-camera?

A: Any shotgun can be rigged on camera: Here are a few things to keep in mind: 1) You will need XLR input with phantom poer. If your camera only sports a mini input, you will need some sort of an XLR adapter device such as a beachtek adapter "with phantom power) to allow the use of this mic. 2) If this is going onto a smaller form factor camera and especially if you are using a wider angle lens, this mic may be in the frame, so this may not be your best choice then and you may want to opt for a shorter microphone. 3) Shotgun mics are very sensitive to handling noise, so make sure you get a shockmount to go with this mic in order to minimize handling noise.