Making arts & crafts sometimes requires being able to cut into tight areas where other blades can't reach. This pack of four Slice Corner Stripping Blades - Pack of 4from Slice Corner Stripping Blades - Pack of 4are ideal blades for such a task. The zirconium oxide ceramic blade has a finger-friendly single edge, which is sharp for materials, but resistant to cutting skin, and the pointed tip can be used to initiate a cut into wood, clay, or other materials. Also, the blades are non-conductive, non-magnetic, non-sparking, and chemically inert, so they will never rust. The oil- and lubricant-free blades are compatible with the 10548 craft knife, 10589 craft knife (safety cap), 10568 scalpel, and 10580 precision knife handles.

For Stripping & Trimming in Tight Areas    Zirconium Oxide Ceramic Blade    Single-Edge, Pointed Tip to Initiate Cut    Finger-Friendly Safety Edge    Non-Sparking and Chemically Inert    Non-Conductive and Non-Magnetic    Oil- and Lubricant-Free Blade    Blades Compatible with Select Handles

Handles: 10548 craft knife, 10589 craft knife (safety cap), 10568 scalpel, and 10580 precision knife

Related Questions and Answers

Q: 1. Would their be a space If you used this corner to create a V-Flat with two scrim jims?

A: There would be a small gap between the frames when using this connector to form a V-flat.

Q: 2. Does this come with a single corner or is it a full set of 4? Also, similar question for the matching Ears (409500-3) - is it a single item or a full set?

A: These are sold individually.

Q: 3. Will the blades easily cut through 18.5 mil (340 gsm) thick paper?

A: The Slice 10580 Precision Knife has a 15.5 mm (0.61 in) cutting depth, which will handle 18.5 mil thick paper.

Q: 4. Does this come with a single corner or a full set of 4?

A: This is a single corner.

Q: 5. Inside dimensions? Also will use this for a butterfly set-up. Any structural problems with a butterfly using this updated corner? Using 1 square aluminum tube from hardware outlet.

A: None at all

Q: 6. There's only one knob. Does that mean the other 1" square tube is permanently attached to the corner?

A: Both tubes are removable. One is secured with a t-handle and the other is secured with a set screw. This is designed to allow for the frames to be stored easily and half built, also so the t-handles don't interfere with one another.

Q: 7. What are the inside dimensions ?

A: As per the manufacture. The inside diameter off that circle is 1,420mm or approximately 4’ 7-29/32”. The truss itself is 290mm or 11-27/64” in width (hence 2,000 – 290 – 290 = 1,420mm). Please note that as this is a welded product these dimensions may vary slightly.

Q: 8. What are the exact dimensions of the part that would go inside the square tubing NOT counting the height of the locking button? B&H specifies that as 2.9cm , but it's not clear if that's including or excluding the height of the locking button.

A: The 2.9cm specification includes the button which extends .45cm further than the inserted portion of the corner. The button clip is necessary for using the Scrim Jim Cine corner as it was intended.

Q: 9. Hi there. What is the maximium diameter pipe it can accept?

A: The Matthews Hollywood Corner - Set of 4 BH #MAHWC is designed for 1" square tubing.

Q: 10. What existing Scrim Jim parts would be required to put together a 72 (apx) by 30 v-flat frame?

A: Westcott offers a pre-packed kit which is similar to a V-flat. That kit would be the Westcott theC47 Book Light Kit B&H # WE2092 , which includes all the necessary components already. Please see the image below for reference.