Use this EDDYCAM Camera Plate 1 | Compact & Durable Camera Mountto hold your DSLR/mirrorless camera and lens. The plate has a two-piece design, is UniQ/C and Arca-type compatible, and can accept EDDYCAM SLiNG straps. Two hard rubber layers provide scratch protection for your gear.

Holds DSLR with Lens    UniQ/C, Arca-Type Compatibility    Two-Piece Design    EDDYCAM Sling Strap Compatibility    Hard-Rubber Scratch Protection    Made in Germany

Related Questions and Answers

Q: 1. Would the screw holes on the back of this suit attaching a Sony RM-B170 unit? It looks like it will, but I can't find a spec sheet detailing the dimensions of the screws.

A: Sorry, we have not heard of attaching a battery directly to a CCU before and are therefore we are unsure that what you wish to accomplish is possible. So that we may be of further assistance with your application, please email us at provideo@a href= http://bhphoto.com target= _blank bhphoto.com./a

Q: 2. What does it bottom looks like? Does it has 1/4 or 3/8 screws?

A: it has both 1/4 20 and 3/8 16 threaded holes on the bottom.

Q: 3. How long is this strap?

A: The EDDYCAM SLiNG -1 Wrist Strap (Black) is approxemelty 5,2 inches.

Q: 4. would this work with a7ii?

A: All the a7 cameras share the same battery so yes this will work on the a7II.

Q: 5. Can you power a camera from the D-tap if i want to put the V-mount on a cheese plate? I had a V-mount before that would not power the camera straight from the D-tap, so just want to make sure this isn't a common thing...

A: I doubt u can power the camera from the d tap. If im right it outputs only 5volts that may not be adequate for the camera. I may be wrong though.

Q: 6. What is the difference between this, mfr no. 5051, and the "non-shoulder" version, mfr no. 5001?

A: The "Shoulder Version" is extremely slip resistant through the implementation of an innovative material combination of Finnish elk leather on the outside and Mongolian yak leather on the inside. The "Non Shoulder Version" does not have the Mongolian yak leather on the inside.

Q: 7. How can you mount this to a 15mm rod setup?

A: Hi Michel. To mount this battery plate to 15mm rods, you would first need to attach it to our Battery Slide (a href= https://www.woodencamera.com/battery-slide-p/156600.htm target= _blank https://www.woodencamera.com/battery-slide-p/156600.htm/a). From there, you can install our Rod Clamp (15mm LW) (a href= https://www.woodencamera.com/rod-clamp-15mm-lw-p/150200.htm target= _blank https://www.woodencamera.com/rod-clamp-15mm-lw-p/150200.htm/a), which will allow you to slide the configuration onto 15mm rods. You can also consider attaching the battery plate to our Battery Swing (a href= https://www.woodencamera.com/battery-swing-p/245700.htm target= _blank https://www.woodencamera.com/battery-swing-p/245700.htm/a), which has a rod clamp pre-installed.

Q: 8. will this clamp fit around the 30mm Movi pro ring?

A: Hi Andrew. Yes, this unit will be able to clamp onto the MoVi Pro ring.

Q: 9. will this work on the a7III camera?

A: This device is for cameras like the a7R II that take the Sony NP-FW50 Lithium-Ion Rechargeable Battery (1020mAh) B&H # SONPFW50. It is a very small battery. That is why it was it was replace by the larger Sony NP-FZ100 Rechargeable Lithium-Ion Battery (2280mAh) B&H # SONPFZ100. This is the battery the a7 III uses. Since it is larger, the Wooden Camera V-Mount Plate for Sony A7 and Alpha Cameras B&H # WO181200 will not work.

Q: 10. Can this plate power an Ikan VH8 monitor? If not, is there one that will? Looks like it only has a D-tap connection...

A: This plate is not compatible with the Ikan VH8 monitor. We are not aware of a V-Mount plate that is compatible at this time.