The 7.68-inch long DigitalFoto Inner Screw Magic Arm 7.68"is an arm for attaching and positioning available accessories to your camera or other 1/4"-20 mounting point. It features a 1/4"-20 thread on each end and supports up to 8.8 pounds. It is machined from anodized aluminum and stainless steel for strength and features three points of articulation that tighten and loosen using a single locking knob.

The ends of the arm are set into ball joints, with each joint providing swivel and lockable position adjustment. Each end features a rubber-topped platform that the thread extends out of and a thumbwheel that allows you to tighten your accessory on the mount. One end features raised metal fittings that make this compatible with the EZ-Link system when using the included 1/4"-20 to 3/8"-16 adapter bushings.

Three Points of Articulation    Unfolds to 7.68 Inches    Supports up to 8.8 Pounds    Metal Construction    Center Locking Twist Handle    Ball Joint End with 1/4"-20 Thread    Compatible with EZ-Link System    Includes 1/4"-20 to 3/8"-16 Bushings

When the arm is loose, the center pivot and both ball joint ends are flexible and can be moved to almost any position. Tightening the center twist lock tightens the center pivot as well as both ball ends at the same time.

Related Questions and Answers

Q: 1. Are these 25mm balls? Would like to use them with a magic arm that uses 25mm.

A: Yes, the Kondor Blue Ball Head with 3/8"-16 ARRI-Style Anti-Twist Screw for Magic Arm (Gray) is 25mm.

Q: 2. What is the size range of the pipe diameter to which this can be clamped?

A: Up to 1 3/4".

Q: 3. What's the weight capacity of this arm ?

A: I believe the weight limit is 12 lbs. But it would feel sturdier with less than 10. In my opinion.

Q: 4. Is it possible to get the anti-twist pins off the system?

A: For the Kondor Blue Ball Head with 3/8--16 ARRI-Style Anti-Twist Screw for Magic Arm (Black), we are not aware of any official way to remove the anti-twist pins.

Q: 5. hi, i see this arm has a hot shoe mount. does that hot shoe come off so that the arm will have a 1/4-20 thread on each end?thankstony

A: Yes, the shoe mount can be removed leaving a female 1/4 -20 thread. The female 1/4 -20 coupler can then be removed ultimately leaving a male 1/4 -20 on both ends.

Q: 6. Will this work with the Ronin SC to mount a small monitor?

A: Yes, this should work with the Ronin-SC as well.

Q: 7. I have a projector with a tripod female connector, will I be able to connect the projector to the arm?

A: Yes, it has a 1/4-20" stud to attach to your projector but the load capacity is only 4lbs, may not hold it.

Q: 8. Will this work with MIOPS splash kit?

A: Yes, The Pluto Magic Arm with Clamp will work with Miops splash kit.

Q: 9. Will it connect to a boom stand? Any point in buying it without the stand?

A: Yes, the Pluto Magic Arm with Clamp will connect to a boom stand.

Q: 10. Are the locating pins Arri 1/4-20 standard? Will the pins match up to the SmallHD Cine 7?

A: Yes, the SmallRig Magic Arm with Dual Ball Heads (1/4"-20 Screw and NATO Clamp) has a standard Arri-Style 1/4"-20 pins and will attach to the bottom or sides of the SmallHD Cine 7 Touchscreen On-Camera Monitor (L-Series), B&H # SMMONCINE7.