Use this stainless-steel CAMVATE 1/4"-20 to 3/8"-16 Tripod Screw Adapter (2-Pack)from CAMVATE 1/4"-20 to 3/8"-16 Tripod Screw Adapter (2-Pack)to connect cameras, plates, and tripods that have 1/4"-20 male screws and 3/8"-16 female threads. The small head features a flat head screw type. Two screw adapters are included in this pack.

Two Screw Adapters Included    Use with Camera, Tripods, or Plates    Stainless-Steel Construction    Flat Head Screw Type

Related Questions and Answers

Q: 1. I ordered this and it was not the Right screw for me what is the right one where I can slide it down a mounting bar after threading it in? Something longer.

A: A shoulder screw seems the appropriate fastener if I understand the situation. These have a threaded portion at the end of the shaft and an unthreaded portion beneath the head. The shoulder is formed at the border between the two portions, the unthreaded area being of greater diameter than the threaded. This shoulder allows the screw to be secured in the camera before it bottoms out in the hole. Please try a search for 'shoulder screws' to understand the variety of configurations or visit a good hardware store. The standard 1/4-20 threading applies.

Q: 2. I'm considering using this to attach an Arca Swiss plate to my camera. What is the diameter of the split ring? Regards, David.

A: The split ring on the CAMVATE Split Ring with 1/4"-20 Screw for Tripod/Camera Attachment has an external diameter of 29mm, while the internal diameter is 27mm.

Q: 3. Is it made of aluminum or steel?

A: This is believed to be made of steel.

Q: 4. Can this be attached to a 75mmx75mm VESA mount?

A: No, it appears that the maximum spacing for the 1/4"-20 screw threads is 72mm.

Q: 5. What is the mm spacing between the two 1/4-20 screws on center?

A: The spacing between the two 1/4-20 threads on the CAMVATE 0B 2-Pin Female 1 to 3 Power Splitter Adapter Box with 1/4"-20 Screw Mount is 7mm. However you can slide the 2nd screw down up too 14mm away from the first screw.

Q: 6. Does the screw allow you to adjust the tension of the tilt mount so that you can adjust the angle on the fly and have it stay put, or do you have to use the screwdriver to loosen and tighten the screw to lock it down every time you want to adjust it?

A: With the CAMVATE Tilting Shoe Adapter Support with 1/4"-20 Screw for Monitor/Light, you need to use the included screwdriver to loosen and tighten the tilt.

Q: 7. Will this fit the side mount on a Feiyu Tech G6 gimbel?

A: yes no problem to set the C0993 1/4 -20 Mount to Shoe Adapter is 1/4 for you G6 on side also on baton to mount on tripod!

Q: 8. How long is the thread? Long enough to affix an Arca-Swiss plate to the bottom of a camera?

A: CRDBAG 1/4"-20 D-Ring Camera Screw (4-Pack) are 4mm long. For arca swiss plates you will need at least a 10mm screw with a neck.

Q: 9. What's the wight they can hold

A: The CAMVATE 1/4"-20 Mini Ball Head can hold 4.4lb.

Q: 10. i have a Sony A7iii. The Tripod Mounting Thread is 1 x 1/4"-20 Female (Bottom). I need to screw the camera onto a quick-release plate. Will this item work? TIA!

A: CAMVATE 1/4"-20 Female to 3/8"-16 Male Screw Adapter for Tripod (2-Pack) won't work as it fits screw openings that are 3/8".