The CAMVATE 7" Articulated Arm Monitor Mountfrom CAMVATE 7" Articulated Arm Monitor Mountfeatures a 1/4"-20 male thread and 25mm rod clamp on both sides. It is used to install any device with a 1/4"-20 thread hole, such as a 7" screen monitor, to a 25mm rod or pipe. It is compatible with DJI Ronin-M and Freefly MoVI stabilizers and supports a load up to 6.6 lb.

2 x 1/4"-20 Male Thread & 25mm Rod Clamp    6.6 lb Maximum Load    For DJI Ronin-M & Freefly MoVI

Related Questions and Answers

Q: 1. How much weight can this support?

A: At least 4lb

Q: 2. Can you remove this arm from the clamp, if so does it have a standard tripod 1/4 20 thread?

A: The clamp is locked onto the arm with Loctite. It is not meant to be detached. If you contact GyroVu directly, they can assemble one for you without the Loctite.

Q: 3. Can this be used to mount an AD200 strobe with a 1'x3' strip box? Does it articulate horizontally and vertically?

A: If you purchase the Impact 5/8" Stud with 1/4"-20 Female Threads, B&H # IMSRP112P, the Godox S2 Speedlite Bracket for Bowens, B&H # GOS2, and your softbox with a Bowens speedring adapter, and the setup weighs less than 11 lbs, then yes, the Godox AD200Pro TTL Pocket Flash Kit should be compatible for use with the Manfrotto Double Articulated Arm - 3 Sections With Camera Bracket. The articulating arm will only adjust in one plane of motion; either horizontally or vertically, but not both (depending on how the arm is orientated in the clamp/grip head you are using to hold the articulated arm).

Q: 4. Could the arm be used as an attachment on a C-Stand?

A: i used a super clamp and it holds..

Q: 5. Can you remove the shoe mount to have 1/4-20 at each end?

A: Yes, the hot shoe mount can be unscrewed.

Q: 6. Is this compatible with the ALZO Wall Mount with Ball Head for Camera ? https://a href= http://www.bhphotovideo.com/c/product/1337728-REG/Wall_Mount_with_Ball_Head_for_Camera target= _blank www.bhphotovideo.com/c/product/1337728-REG/Wall_Mount_with_Ball_Head_for_Camera/a

A: The Avenger F301 Baby Wall Plate (Chrome-plated) B&H # AVF301 is compatible with this Manfrotto arm as it uses a 5/8 receiver for one of the pins on the arm.

Q: 7. weight limit?

A: This is not a rigid structure and the camera will move around if you bump it at all. I don't know the exact maximum limit . I have used it with a Canon EOS 70D and Sigma 18-50 mm zoom. I use remote release or with release through software on my laptop.

Q: 8. would this 11" arm be good for mounting a Godox M1 (B&H # GOM1) to something like an oben Table top tripod (BH #OBTT100)? I don't want to use something ridiculously large like a full blown cstand/lightstand/camera tripod to mount a 1/2 lb godox M1 unit, but would like more angle and height versatility, that presumably a 11" arm would give. But not sure if it's a wise way to get there, if the 11" arm would be too top heavy for the oben tabletop tripod/tip over, etc. I would be looking to use it in vehicle interiors and behind subjects of a greenscreen to create separation. I find having the tabletop pod on the floor or on a carseat isnt verstatile enough (light looks too underlit and unnatural) and don't have places to clamp the godox m1 inside a car without damaging cars i don't own, etc. And similarly, the angle of the light for backlighting a subject to create separation w a greenscreen isn't high off the ground enough to get an effective wrap around a seated subject, if am just using the tripod on the floor. Plus it would be great to be able to angle the light to fine tune a greenscreen key, etc.

A: The Manfrotto 209 Tabletop Tripod (BH #MA209), would be more suitable to support the Gyrovu Heavy-Duty Articulated Arm (11-), as it has a much higher load capacity. You may also want to consider a small sandbag for further reaches of the arm with the Godox M1 light. https://bhpho.to/3CWx6en

Q: 9. Can this hold up the weight of a DSLR camera with macro lens?

A: I have attached my Canon 70D with a 24-70 mm 2.8 L lens without issue.

Q: 10. What is the maximum length of this fully extended and the individual length of each arm?

A: Fully extended it is about a 6 length. The two arms are about 3 .