The Slik Pro CF-633 Tripod Black - Compact & Lightweightis constructed from carbon fiber to maximize durability while limiting weight. It supports up to 6.6 lb and measures 21.3" when folded. Each of its 3-section legs features an independent spread, a 3-position angle lock, twist locks for rapid deployment, and rubber feet help to enhance stability on a wide variety of surfaces. The included push-and-pull, rapid center column is removable, which permits a minimum height of 4.9". The SLIK Pro CF-633 Tripod provides a maximum height of 48.8" and 64.2" with the column fully raised.

Tripod heads, cameras, lenses, or sport optics with 1/4"-20 or 3/8"-16 female accessory threads can be directly connected to the reversible mount on top of the tripod's center column. For added versatility, the center column is reversible, facilitating low-angle photography where an attached camera is positioned among the tripod's legs instead of above them.

Load Capacity: 6.6 lb    Max Height: 64.2", Min Height: 4.9"    Folded Length: 21.3"    Leg Sections: 3, Weight: 2.1 lb    Carbon Fiber Legs    Twist Locks, Rubber Feet    3-Position Leg Angle Locks    Reversible, Rapid Column    Reversible 1/4"-20 and 3/8"-16 Mount

• Supports up to 6.6 lb
• Push-and-pull center column with ballast hook for rapid camera, lens, or sport optic positioning
• Center column is removable, which allows the tripod to be set at a minimum height of 4.9"
• Tripod can be set to a maximum height of 48.8" and 64.2" with the column fully raised
• Column is reversible, facilitating low-angle photography where an attached camera is positioned among the tripod's legs instead of above them
• Legs each feature three sections, an independent spread, a 3-position angle lock, and a twist lock for rapid deployment
• Rubber feet for stability
• Weighs 2.1 lb, measures 21.3" when folded

• Carbon fiber legs
• Center column platform with reversible 1/4"-20 and 3/8"-16 mount

Related Questions and Answers

Q: 1. Is the center column removable and if so then how low it can go to the ground?

A: With the Slik Pro CF-733 Tripod (Black) one can remove the lower part of the center column to get lower to the ground. One can then get down to 8.3" (This does not include the height of any head one may use). Alternatively one can invert the center column to get even lower to the ground.

Q: 2. Would this be a good option for holding a Canon 5D Mark IV with a 70-200mm lens attached? Based on the max weight of this tripod, that combination should work well correct?

A: We would probably suggest a unit with a 10lbs payload the following unit only supports a 6.6 payload system. Review the following unit which will support more of a payload Slik Pro CF-733 Tripod (Black) BH #SLPCF733 • MFR #615-924 https://bhpho.to/3E08hhQ

Q: 3. What is the length of the center column?

A: While the manufacturer does not list the total length of the center column, Slik USA does indicate that the maximum height when the center column is down is 48.8 inches, and the maximum height when the center column is fully extended is 64.2 inches. As such, the center column would have 15.4 inches (39.11 cm) of travel from the lowest to highest setting.

Q: 4. "Center column is removable, which allows the tripod to be set at a minimum height of 4.9" How can it be used without the center column, unless there is a short one available to take its place?

A: The center column splits near the top, turning it into a short center column.

Q: 5. What is the thread size?

A: This tripod has a reversible screw. One side is 1/4" the other side is 3/8".

Q: 6. What is the outside diameter of the top of the center column (where a head would be mounted)?

A: According to Slik USA, the platform plate on the top of the center column on the Slick CF-633 tripod is 1-5/8" in diameter.

Q: 7. What is the diameter of the base plate (where the head attaches)? Would the manfrotto befree video head fit on this neatly, says it is best that it be a 40mm base plate?

A: The base plate is about 2" wide, and would fit the Manfrotto BeFree video head quite nicely on it.

Q: 8. Hi, What is the leg tube diameter of the CF-834?

A: Slik Pro CF-834 Tripod is a 4 section leg tripod. Stating from the thinnest to the thickest section they increment as fallow: (19 ,22 , 25, 27mm)

Q: 9. What are the diameters of the leg sections?

A: Slik Pro Pod CF-834 Monopod has four leg section starting from the top the legs diameters are 28, 25, 22 and 19 millimeters. The rubber pad on the top has a 32mm diameter.

Q: 10. is this tripod compatible with the Panasonic DVX100b ?

A: The DST-3 Lightweight 2-Stage Tripod System is compatible with the DVX100B.