Clearly identify your cables and avoid time-wasting confusion with the white Neutrik BSE-9, a colored bushing designed specifically for use with select Neutrik etherCON cable connectors. Made for easy installation on Neutrik NE8MX, NE8MX-B, NE8MC, and NE8MC-B connectors, the BSE-9 is attached between the shell and strain relief of your compatible connector.

For Select Neutrik etherCON Connectors    Fits NE8MX, NE8MX-B, NE8MC, and NE8MC-B    Allows Clear Identification of Cables    Easy Installation

Related Questions and Answers

Q: 1. Are these shielding compatible? I want to use these to bring two shielded etherCon cables together between SoundTools CAT Tails. Will these carry the shielding/ground in-line?

A: Yes the NE8FFX6-W coupler is compatible with shielded CAT6a ethercon lines.

Q: 2. How is it possible that this thing costs $341? Does it come with a microphone?

A: No, it doesn't come with a microphone.

Q: 3. Will this cover work for the switchcraft D panel rocker switch?

A: Yes, The Neutrik SCCD-W Spring-Loaded Cover for Select Chassis Connectors is designed to work with Panel connectors like the Switchcraft D panel connectors. Compatibility XLR D Series female XLR D Series male 1/4" Jacks D Series speakON NL2M* and NL4M* powerCON 20 A Series NAC3MPA* and NAC3MPB* powerCON TRUE1 NAC3MPX opticalCON chassis connectors USB NAUSB-W* HDMI NAHDMI-W* D-SUB NADB* Firewire NA1394-6-W* etherCON D Series etherCON CAT6 chassis connectors etherCON CAT6A chassis connectors BNC D Series Phono (RCA) chassis connectors Note: Maximum allowed opening angle during installation is 100°. Maximum panel thickness is 0.06"/1.5mm in combination with ether CON NE8FD* receptacle.

Q: 4. does this work with lumix gx85 or Olympus omd 10 Mark ii?

A: If you own a standard (full-sized) hot shoe speedlight flash that is designed to connect to the Panasonic Lumix DMC-GX85 Mirrorless Micro Four Thirds Digital Camera or the Olympus OM-D E-M10 Mark II Mirrorless Micro Four Thirds Digital Camera, then yes, the Vello Universal Softbox with Colored Gels and Cinch Strap Kit should be compatible with your hot shoe flash.

Q: 5. could 2 of these be used to mount 1.5" pipe to the top of C-stands?

A: This would not be suitable for 1.5" pipe. Compatibility 1.65 - 2.05" (42 - 52 mm) round tube

Q: 6. Can I mount a Sony FX3 to this arm???

A: No. The following unit offers a 5 lb Maximum Weight Capacity.

Q: 7. Does the connectors come with magnets,such that both the connectors can be joined together when taken out from the camera beads?

A: No, the PGYTECH Quick Connectors with Quick Beads do not have any magnets installed in them.

Q: 8. What are the inside dimensions of the included liner please?

A: The inner liner is foam and has a slow ripple out from the hard edge. To the inside of that ripple is 6 1/8 long and 3 1/2 wide. I use it to store a Tascam DR-40 digital recorder. It's tight on the long side and has room to store the USB cable, and an extra memory chip in a small case. Hope this helps.

Q: 9. Can this handle the SDI-6G signal from Blackbagic's Mini Converter HDMI to SDI 4K? How long can the cable be? Will a signal booster be required?

A: Hi David,This cable can be up to 200' in length as long as the device (Black Magic unit) has the proper settings, which pertains to the clocking. Up to that length a signal booster would not be required.

Q: 10. Can this work with my TSA 002 Fender hard case guitar handle?

A: It would depend on the model of your case. This handle is designed for SKB iSeries cases, a list of compatible models can be found in the overview section of this listing.