The Pelican 1520 Watertight Case with Foam (Silver) is an unbreakable, watertight, airtight, dustproof, chemical-resistant and corrosion-proof hard case used to carry any kind of equipment that needs to be protected from the elements. It is made of Ultra High Impact structural copolymer, which makes it extremely strong and durable. It includes a 0.25" (6.4mm) neoprene o-ring, ABS latches that seal perfectly, and an automatic purge valve for quick equalization after changes in atmospheric pressure.

The 1520 case meets ATA standards for transit cases, is NATO-codified, and is tested to MIL C-4150J (Military Standard) and IP-67 (Ingress Protection).

This case includes a three piece foam insert set.

Watertight, Dustproof Case    Made of Ultra High Impact Copolymer    Three Piece Foam Set is Included    Built-in Pressure Equalization Valve    Two Double Throw Latches    Padlock Protectors    Rubber Over Molded Handle

Unbreakable, watertight, airtight, dustproof, chemical-resistant and corrosion-proof case

Made of Ultra High Impact structural copolymer that makes it extremely strong and durable

Includes a three piece foam set that consists of one "egg crate" foam upper section, one Pick 'N Pluck foam section and one 1.0" blank bottom foam section

Built-in automatic pressure equalization valve for changes in altitude or temperature

Temperature rating -10 to +210° F (-23 to +99° C)

Easy open Double Throw latches

Stainless steel hardware

Padlock protectors provide added strength and extra security against cutting and theft

Comfortable rubber over-molded handle

• IP67 (1 meter submersion for 30 minutes) (Ingress Protection)
• MIL C-4150J (Military Standard)
• Def Stan 81-41/STANAG 4280

Related Questions and Answers

Q: 1. Will the Pelican 1615NF hold a Nikon 600mm F4E lens with attached hood in shooting position, coupled to a Nikon D5?

A: The D5, the NIKKOR 600mm f/4E, and the hood will be approximately 28" in length. However, the width of the case is in only 29.6" so there is not enough room for enough padding. 3" is a minimum for such a large lens. As a motion picture camera assistant who routinely worked with $100,000 cine lenses and shipped them frequently, I can tell you that shipping an expensive lens with the hood on is not recommended. The case could be dropped and the leverage of the hood could cause very expensive damage to an already expensive lens. I understand the desire to have the camera, lens and hood all set ready to go because no one wishes to lose a special shot. However, for the long haul, I strongly recommend that you not ship the lens attached to the hood or even the camera. Shipping your camera and lens unattached will mean your gear will arrive safely and be ready to work properly.

Q: 2. Will this case be able to hold a NIKON D610 with a battery grip connected? Not interested if the camera and grip has to be put on its side or upside down Please help. Thanks

A: I wouldnt recommend the height of this case to house a Nikon D610 + battery grip because the Nikon would be 4.4 high and then adding the battery grip I was looking at it is 1.8 for a total of 6.2 leaving hardly and room in the 1520 case. It is only 6.7-8 wide to fit inside.Robert

Q: 3. I want to use this case for my elinchrom lights. Preferred to put all 4 FX 400 and may be soon enough the new ELC HD pro lights. I am not able to make out if with foam i can put all 4 in this or is there another hard case i can use?

A: No, based of measurements the case will not accommodate a qty of 4 FX 400 ELC heads. Please review the following case to fit all four heads

Q: 4. Can this fit a manfrotto 502 tripod?

A: Yes Manfrotto 502AH Video Head & MT055XPRO3 Aluminum Tripod Kit can fit in this case once the dividers are rearranged.

Q: 5. Can this fit an Aputure 600d, 300d, & 120d with ballasts?

A: No, the Pelican 1615AirTP Wheeled Hard Case is too small for the Aputure 600d, 300d, & 120d with ballasts.

Q: 6. Can this case be used without the lid organizer and Packing Cubes, as just the empty shell?

A: The Packing cubes on the Pelican 1615TRVL Wheeled Check-In Case Lid Organizer and Packing Cubes can be taken of the case. the lid organizer can not be removed.

Q: 7. Can you fit a SmallHD 1703 P3X 17" production monitor inside?

A: Yes this case will fit the SmallHD 1703 P3X 17" Production Monitor.

Q: 8. Will the TSA cut off the locks I put on them even if I offer to give them the key?

A: Yes. Please review the following locks that will not get cut off as TSA has keys to open already. https://bhpho.to/3mBfwDw

Q: 9. Is this big enough for light stands and tripods? Or is there a better hard case for that application?

A: It will ultimately depend on the amount of lightstands you have and their dimensions. Internally, this is 29.6" long, so it might fit a few 6' stands, but maybe not a 8~10' depending on its dimensions. Cases specifically for stands do exist, like this SKB roto-molded stand/tripod case: https://www.bhphotovideo.com/c/product/1030290-REG/skb_1skb_r3709w_roto_molded_tripod_case_with.html

Q: 10. What is the diameter of the lock holes on the Pelican 1520 case?

A: The is approximately 7mm.