Ram Tough-Ball M10-1.5 X 25Mm Threaded Stud Mount

Ram Tough-ball M10-1.5 X 25mm Threaded Stud Mount

Product Code: eq65931
Availability: In Stock

$40.47 $53.83

Qty

14 reviews Write a review

Description
Reviews (14)

The RAM Tough-Ball M10-1.5 x 25mm Threaded Stud Mountfrom RAM Tough-Ball M10-1.5 x 25mm Threaded Stud Mountconsists of a 1.5" diameter RAM Tough-Ball connected to a M10 1.5 x 25mm threaded post. This threaded post matches the thread holes found on a variety of electronic devices.

High-Strength Composite Stainless Steel Threads

General
Dimensions	Not Specified by Manufacturer
Weight	0.19 lb / 0.09 kg
Packaging Info
Package Weight	0.2 lb
Box Dimensions (LxWxH)	4.85 x 2.5 x 1.95"

Related Questions and Answers

Q: 1. How big is the hole through the middle? Is it big enough to fit a 15mm rod and, if so, is there a way to secure it?

A: The hole in the middle is 20mm in diameter. Since it is meant only for weight reduction, no means of securing is integral with it.

Q: 2. What is the length?

A: 2 1/2

Q: 3. Is this compatible with the SmallHD Cine 7 monitor?

A: Yes, the SmallHD Cine 7, has x4 1/4" mounts with locating divots, which can accept the screw and pin set from the Ultralight 25mm Ball Adapter Monitor Mount for SmallHD On-Camera Monitors.

Q: 4. How much weight does this mount support?

A: Hi Ethan, According to the manufacturer, this ball head mount will support up to 3.3 lb.

Q: 5. extra locking screws part number?

A: We don't currently sell additional locking screws. You would need to contact Fujinon directly to order more. They can be contacted at 973-633-5600.

Q: 6. Is it made of aluminum or steel?

A: The SmallRig Double Ball Head with Cold Shoe & 1/4"-20 Stud is made of an aluminum alloy plus stainless steel.

Q: 7. Can the cold shoe be removed and used as 1/4" screw?

A: Yes it does.

Q: 8. Can this ball head be attached to the following Smallrig handle? I'm using the ball head to connect a monitor

A: If the handle has a cold shoe, yes it will attach just fine.

Q: 9. Will this work with Lightbridge CRLS?

A: The Godox Rail Mount Stud for KNOWLED LiteFlow is very similar to the Lightbridge CRLS system. Godox says it should fit. But the are not 100 percent and it has not been tested.

Q: 10. Silly question : how many pieces in 1 order? I'm assuming it's 1 piece, not a pair yeah?

A: Yes, one, not a pair.

Alfonso	26/09/2024
[0.2 lb] These will not turn or loosen since they have the nut insert at the base... perfect for my navigation tablet! 5

Patrick	13/09/2024
[0.2 lb] When gripped with a ram mount clamp, these ram mounts hold a lot of weight without sag. I use them to mount a monitor on my camera. I did find that the aluminum threads do wear out over time. 5

Craig	02/09/2024
[0.2 lb] This is the perfect solution for my Garmin echomap�44. It fits perfectly tucked in a tight little area on my boat. It allows for adjustment but doesn't�budge once tightened. Although ram sells a wire hider mount I made my own to fit my requirements�out of Azec�board. 5

Craig	02/09/2024
[0.2 lb] This is the perfect solution for my Garmin echomap�44. It fits perfectly tucked in a tight little area on my boat. It allows for adjustment but doesn't�budge once tightened. Although ram sells a wire hider mount I made my own to fit my requirements�out of Azec�board. 5

Ann	18/08/2024
[0.2 lb] I luv RAM products. Other people said there were not enough threads so I was hesitant to buy....but there were PLENTY of threads for a secure connection. You can see us using the product in our videos at MrRuminate (no spaces, no punctuation) on YouTube. 5

James	03/06/2024
[0.2 lb] This solid piece replaced a cheap plastic ball that had an aluminum threaded bolt. 5

Uwe	29/05/2024
[0.2 lb] It is doing what it should. 5

KHIAM NENG H.	27/05/2024
[0.2 lb] Use this to secure to your device with standard camera hole. 5

Dan	22/05/2024
[0.2 lb] Threaded stud is appropriate length to work with camera/gear 1/4-20 mounts. Makes it easy to use Ram Mounts rigging for mounting an external monitor--rock solid. 5

David	19/05/2024
[0.2 lb] Using this as part of my LED light whip, made from an antenna. The threaded part of this ball fits the spring of the antenna perfectly. It’s a very strong mount that can be adjusted as needed. 5