Dock your Steadicam-type arm between shots onto an INOVATIV cart with this FLOWCINE xPeg Rip-Tie for Steadicam Armfrom Flowcine. The xPeg clamps to the edge of the cart and the arm docks on the peg which is made of rubber to protect your gear.

The outside of the xPeg is coated with a soft bumper material to further protect the cart and your gear from scuffs and scratches. A 12" long hook-and-loop strip can hook around the cart for additional support, or it can be used as a cable tie. There's also a 3/8"-16 mounting thread in the xPeg for mounting additional gear.

Dock Steadicam-Type Arm on Cart Shelf    Compatible with Any INOVATIV Cart    Rubber Tip for Safely Mounting Arm    12" Hook-and-Loop Strap to Tie Down Arm    1 x 3/8"-16 Thread    Internal Spring Mechanism    Soft Protection Bumper Material

Related Questions and Answers

Q: 1. Do you have an estimate on when these units from Cinemilled might be arriving? I'm from Canada, so the pre-ordering process doesn't work as well for me based on shipping prices. Thanks in advance!

A: Sorry, but we do not have a date of arrival for these units. Hopefully soon.

Q: 2. Would this mount a CameTV arm? Or is an adapter in the works to allow this?

A: This product is listed as compatible with Steadicam Arms with Pin mounting.

Q: 3. Hi I have a Tiffen master series arm and Djı ronin 2 Which size should I take?

A: From what I can gather, this unit will not fit a master series arm.

Q: 4. Will this work with the Glidecam x-22?

A: Hello there...The best thing to do would be to phone Cinemilled Customer service and ask them if one of their adaptors would fit the X-22 system; it all comes down to whether or not the X-22 armpost fits the Cinemilled adaptor. I have done a fair bit of research on this for my Glidecam X-10 system and subsequently bought the Cinemilled 7/8 armpost adaptor. The 7/8 adaptor is the recommended (by Cinemilled) hardware for the X-10/DJI Ronin combo. If the armpost for Glidecam arms are all the same then you're good to go with the 7/8 however; since the X-22 supports a heavier payload (10-25lbs) than the X-10 (13lbs), it may very well use a larger post and a different size adaptor. Hey, if the forums have nothing so far the manufacturer would know for sure; all I can say is that once you find the right adaptor, it's a very impressive rig...hope this is helpful!

Q: 5. Will this work with the Glide Gear DNA 6000 arm and vest?

A: This combination is unknown but it should work with any 7/8 post. The Glide Gear DNA 6000 is reported to be 7/8 so you should be good.

Q: 6. Can I store all of the pieces that are my steadicam AERO? or only the arm?

A: This bag will only hold the arm. The bag at the link below will hold the arm & vest:a href= https://www.bhphotovideo.com/c/product/1347263-REG/steadicam_807_7980_steadimate_arm_and_vest.html target= _blank https://www.bhphotovideo.com/c/product/1347263-REG/steadicam_807_7980_steadimate_arm_and_vest.html/a

Q: 7. Could the serene be mounted on an Easyrig Cinema 3 ?

A: Yes, you will be able to mount this pn the Easyrig Cinema 3.

Q: 8. How wide are these straps?

A: Exactly 1/2 . 3/4 where the hole is.

Q: 9. Is it also fit for Steadicam G70 arm? Thanks

A: The Proaim Hard Mount Kit for Steadicam–Type Arm has an Arm Socket pin of 16mm or 5/8". If your Stedicam G70 has the same pin size, then it will be perfectly compatible.

Q: 10. What are the hole sizes in the Cinemilled armpost adapter plate? I'm wondering if using a male to male 1/4 or 3/8 thread adapter, I could attach a Ronin-S to this plate (i.e., not attach the armpost adapter to a gimbal handle bar but just to the bottom of the Ronin-S).

A: We are not aware of a way for this product to be used with the Ronin-S. One portion connect to a 1/2" post from a Steadicam system, while the other connects to a 30mm Top Bar on the original Ronin.