This 300' Whirlwind EtherCON Cat 6a Shielded Ethernet Cable 300ftfrom Whirlwind EtherCON Cat 6a Shielded Ethernet Cable 300ftis designed for professional audio and stage lighting applications. The EtherCON locking metal connectors help to ensure a secure fit. The cables are compatible with other Cat 6a and Cat 5e EtherCON devices and provide thick 24AWG-stranded inner conductors. Supporting the augmented Cat 6a standard, this cable is capable of supporting up to 10 Gb/s over a 328' maximum cable run.

Cat 6a RJ-45 EtherCON Connectors    1 x EtherCON RJ-45 Male    1 x EtherCON RJ-45 Male    Up to 10 Gb/s Data Transfer Rate    300' Cable Length    Shielded to Reduce Crosstalk    24AWG Gauge Cable Thickness

Related Questions and Answers

Q: 1. This accessory serves to transmit photos to a cell phone android?

A: It is designed to be used with the D5 DSLR, and the WT-6A Wireless Transmitter from Nikon in order to enhance the camera's connectivity capabilities. It is not made for just any camera and would be overkill if you just wanted to transfer to an android smartphone.

Q: 2. could this work as a sideline reporter device? how do you plug in to behringer audio board ?

A: Should work and connect via the provided I/O:Mono In: 1 x 3-pin XLR femaleStereo In (L/R): 2 x 3-pin XLR female, balancedMic In: 1 x 3-pin XLR female Phone: 1 x 3.5 mm jack; 1 x 1/4 jackMic Out: 1 x 3-pin XLR male

Q: 3. Does this unit require external power? if so, how much and on what kind of connector?

A: The Whirlwind Line Balancer/Splitter requires no external power and is designed to split a single line level input signal into two balanced line level outputs. A choice of two output configurations is provided: one direct output and one isolated output, or two isolated outputs. The Line Balancer/ Splitter uses Whirlwinds TRSP-600L transformer and has a frequency response of 20 to 20kHz, 1dB @ +2OdBm.On the Line Balancer/Splitter are two male XLR jacks, one female XLR jack, a 14 jack and three switches as outlined below:INPUTEither of the two input connectors, a female XLR jack or a 14 TRS jack (Tip = Pin 2 and Ring = Pin 3) can be used for connection from a line level source, balanced or unbalanced. Use only one input at a time.OUTPUTSThe male XLR output connectors can be configured in one of two ways. The ISOLATED OUT/SPLIT 1 is always transformer isolated and the DIRECT OUT/SPLIT 2 is either directly connected to the input or transformer isolated, depending on the position of the OUTPUT SELECT switch.OUTPUT SELECTThis push-button switch selects the output mode of the unit. In the out position, the DIRECT OUT/SPLIT 2 provides a direct output signal and the ISOLATED OUT/SPLIT 1 provides a balanced 600 isolated signal. In the in position (the center of the switch changes to orange) both output connectors provide a balanced 150 ?isolated signal that is attenuated by 6dB from the input.GND/LIFTSEach of these switches disconnects the ground between the inputs and the XLR outputs when set to the LIFT position. Grounds remain connected when set to the GND position.This product is warranted to be free of defects in materials or workmanship to the original purchaser for a period of 3 years from the date of purchase.

Q: 4. Hi. Does this check phase also?

A: It ONLY tells you if your cables are correctly wired or not. It will not tell what the specific problem is IF there is a problem. This is a very basic, albeit well-made, device. I use it to identify bad cables in the field.

Q: 5. will the WT-6 work in different countries?

A: You will need to make sure that the country you're using the item in will have eligible frequencies for consumer use.

Q: 6. Since the EP-6 is discontinued, will this work with the other EN-EL18 cameras?

A: The Nikon EP-6A Power Connector is only compatible with the Nikon Z9 Mirrorless Camera. You also need the Nikon EH-6D AC Adapter. Here is the link: https://bhpho.to/3mAGBcZ.

Q: 7. Will turning the gain/attenuator knob down all the way mute the output? Or will there still be a noticeable signal?

A: This does not have a bypass or mute so you may hear low level audio with the gain all the way down.

Q: 8. connecting sound from computer through POD DI to go through sound system?

A: You need an audio mixer with XLR inputs to use this PodDI, but yes, this is used to output audio from your laptop or music player through your PA.

Q: 9. Can you use an additional inline barrel pad on top of this in case you need to knock a signal down to mic level?

A: The output is already at mic level. The transformer gives you a 20 dB loss from -10 consumer line input to -30dB. If you need more, there is a built in 20 dB pad switch which takes your signal down to -50dB total. There is no reason or need to use an additional pad.

Q: 10. will this LG 27CN650N monitor play USB videos & repeat without a computer?

A: Yes. The LG 27CN650N-6A 27" 16:9 Widescreen IPS Thin Client Monitor BH #LG27CN650N6A can playback files from USB flash drive devices. The content must have instructions for looping on the drive as there would be no control from this thin-client monitor.