The Casio AD12M3 AC Adapter Replacement Power Supplyis a replacement 12 volt power supply compatible with the following Casio keyboards; the CTK 5000, WK 500/3300/3800, CDP 100/200 and PX 120/320/575/720.

Replacement Adapter for Casio Keyboards

Use only genuine Casio replacement parts and accessories

Related Questions and Answers

Q: 1. How long is the cord from the dummy battery to the connector?

A: The cable length on the dummy battery is 36'' long. The connector cable is 55'' and the Ac cable is 50'' long.

Q: 2. If you use the led bulb 220v 40w, is there a shaking flicker phenomenon? For the shoot.

A: as this is specifically designed for a 50Hz (220/240) scenario there should be no issues

Q: 3. Hi, I am trying to use this with a Canon 5D MKii and I cannot close the battery door. Any ideas on how I can make this happen? Thanks in advance.

A: The battery door has a cut out that allows for the dummy battery cable to slip into.

Q: 4. What is the size of the DC barrel plug? Is it 5.5mm (outer) 2.5mm (inner)? I cannot seem to find this info anywhere.

A: Dracast lists the powersupply for specific models of light and does nto list the size or type of connector.

Q: 5. is this compatible with other 9v gear such as a microKorg?

A: The DC plug on the ON-stage OSADE95 is specific to Casio keyboards only.

Q: 6. Does this work with the Casio PX-350?

A: No, it will not supply enough power. You will want to use the Casio ADA12150P: https://www.bhphotovideo.com/c/product/1317702-REG/casio_ada12150p_12v_adapter_for_px3_5_130_150_160_330_350_360_560_730_750_760.html

Q: 7. there is a center pin inside the jack on my wk3300. I bought what I thought was the right adapter, but the plug end has a center pin also.?what adapter do I need???

A: My adapter was used for a particular piano. It all depends on what you are using your adapter for. You must find the right adapter for the wk3300.

Q: 8. Could work for 110v?

A: The Tether Tools ONsite D-Tap to AC Power Supply (220V) only supports 220v output.

Q: 9. How many volts and how many amps does it output?

A: Hi Taylor, the MX-Charge power supply outputs 7.5W, 1.5A. If you are looking for a 3rd party solution be advised not all USB-C power supplies will run the MixPre series in full power mode. To avoid low-power mode, the MixPre requires a USB power source that flags that it can output 7.5W (1.5A). Many USB power sources can output 7.5W but do not flag that they can do so - these will cause the MixPre to operate in low power mode (maximum two phantom mics, no HDMI in). Use the following for full power:MX-Charge accessoryDual USB-A to USB-C cableApple USB-C power adapter New MacBook Pro USB-C portAny USB power source that flags that it can output 7.5W I hope this is helpful!

Q: 10. Can this be used to charge a V-Mount Battery via the D-Tap port directly in a car? Or is it just a accessory to the ONsite d-Tap AC Power Supply?

A: The ONsite AC Power Supply Car Adapter will not plug directly into D-Tap battery for charging. You would require the Tether Tools ONsite D-Tap to AC Power Supply https://www.bhphotovideo.com/c/product/1438942-REG/tether_tools_sdac110_onsite_d_tap_to_ac.html?sts=pi&pim=Y to plug into the ONsite AC Power Supply Car Adapter. You would then use the charging cable provided with your D-Tap battery to plug into the ONsite AC Power Supply Car Adapter.