The black RSA292 Mini Custom RPA Projector Mount from Chief is used with various InFocus projectors. It features independent roll, pitch, and yaw for fast projector registration and allows for quick connection and easy access to lamp and filters on most projectors. In addition, this mount maintains registration and doesn’t affect preset adjustments even if the projector has been disconnected.

Independent roll, pitch, and yaw for quick and precise projector registration

Quick connect and disconnect with convenient lamp and filter access on most projectors

Disconnecting maintains registration and doesn't affect preset adjustments

All-points security steel-into-steel locking hardware at all connection points protects against theft

Multiple installation options including flush mount to ceiling, use 0.25" threaded rods, or use a 1.5" NPT column

Related Questions and Answers

Q: 1. I just bought a Projector with mounting holes that are 8 apart. I have an existing threaded shaft attached to the ceiling but the plate on it is to small. Can i replace my plate with this and will it extend to 8 ?

A: The mount is adjustable to fit many kinds of projectors. Ours holds a HD photo grade projector that is very large and heavy and it works fine. 8 inches should be no problem. I can't be sure about the plate your talking about but even the top mount is adjustable to fit a variety of brackets and braces so it should work.

Q: 2. Is the total length of the extension 3" (including the threads) or is 3" the exposed part of the extension after the ends are threaded into the ceiling plate & mount?

A: The length of the whole extension column is 3".

Q: 3. Is there a template for mounting

A: NO! Completely unnecessary! Figure the center of where you want the tv, left,right and up,down and mark it with a pencil. Before removing uprights spread them out to max and that is the most they can be mounted apart from each other on the wall. I would subtract an inch to avoid problems. Ideally you want to mount them 22-26 inches apart at the same height. It is all dictated by where your studs are located. Just dont mount to close together, less than 16 inches apart you best keep it centered all the time. Remove the uprights from the crossbars. You can use the same upright to mark both sets of holes. Your template. Use hardware capable of bearing the load(250lbs). If they are mounted at different heights as long as not to much. Half inch or so. There are screws at the top of each to level the bars perfectly. This is probably the BEST TV stand for sale anywhere! GOOD LUCK!!!

Q: 4. Do all the casters lock or only two of them?

A: Two of the casters can be locked to ensure the cart stays securely in place once positioned.

Q: 5. Can i mount an ASUS 34in monitor that ways 24.7 lb / 11.2 kg to this stand?

A: Please note the weight restriction listed below:The ASUS monitor needs to offer one of these compatible VESA mounting standards: 75 x 75mm / 100 x 100mm Compatible Supports Displays Up to 22 lb.

Q: 6. Can I use this upside down? In other words, the pipe will be down and the projector will be right side up?

A: The Peerless-AV PRG Precision Gear Projector Mount for Projectors Weighing Up to 50 lb (Black) BH #PEPRGUNV is not designed for this inverted use.

Q: 7. Is this compatible with the Panasonic FRZ50?

A: The Peerless-AV PRG Precision Gear Projector Mount for Projectors Weighing Up to 50 lb (Black) BH #PEPRGUNV will work with the Panasonic PT-FRZ50WU 5200-Lumen WUXGA Classroom & Office Laser DLP Projector (White)BH #PAPTFRZ50WU.

Q: 8. Can you change the lens

A: This is just a mount for putting up a projector - no lens involved in this product.

Q: 9. What is the distance from the projector to the ceiling?

A: From ceiling to the top of the projector's attachment hole is approximately 4.25 . This is assuming you utilize the included brackets and not use an extension tube.

Q: 10. Will this mount work with the Epson LS-11000 projector?

A: The Peerless-AV PRG Precision Gear Projector Mount for Projectors Weighing Up to 50 lb (White) BH #PEPRGUNVW will mount with the Epson LS-11000 projector.