The Chief FHB3039 Custom Interface for Planar 46" Displays consists of special brackets to ensure that the 46" Planar TV can be installed on Medium FUSION and Thinstall Products Chief mounts. It is also compatible with Universal Thinstall Mounts.

Includes screws and spacers specific to the TV being installed

Related Questions and Answers

Q: 1. Does this work with Nissan i40 for Sony?

A: It should attach to the Nissin i40 Compact Flash for Sony Cameras with Multi Interface Shoe B&H # NIND40S MFR # ND40-S. But it has not been tested. The Multi Interface shoe is a touch larger so you might need to slip it on just right to make sure the center pin will connect. You will need a transmitter too for the camera. It comes in a kit, Vello FreeWave Fusion Basic Wireless Flash Trigger System for Sony Mirrorless Cameras, B&H # VEFWBS2 MFR # FWB-S2.Note this is not a TTL system so the flash will be manual only.

Q: 2. Does this work with Nikon transmitter and Camera for remote shutter release?

A: You can use One of the included receivers on your hotshoe, and use the transmitter to remotely trigger your shutter. Necessary cables are included. Not sure why you'd introduce the other trigger into the system. It may work if it's uses the same frequency. Can't attest to that info.

Q: 3. Is this compatible with my Sony nex 6?

A: This receiver works with Sony compatible flashes which have the Multi-Interface Shoe. You would be better off getting the kit, which comes with the necessary transmitter to fit your NEX 6. That would be the Vello FreeWave Fusion Basic Wireless Flash Trigger System for Sony Cameras with (MIS) Multi Interface Shoe B&H # VEFWBS2.

Q: 4. Is the Chief LTM1U and Chief XTM1U compatible with the Chief "PAC526" in-wall storage box?

A: The Chief LTM1U Fusion Series Tilting Landscape Wall Mount for 37 to 63" Displays (B&H # CHLTM1U) and the Chief XTM1U Fusion Series Tilting Landscape Wall Mount for 55 to 82" Displays (B&H # CHXTM1U) are both larger than the interior dimensions of the Chief PAC526 In-Wall Storage Box (Large), B&H # CHPAC526, and would not be compatible.

Q: 5. What monitors fit these mounts?

A: Monitors 46 to 60" with VESA patterns 200 x 200 mm up to 600 x 400 mm are supported.

Q: 6. Will this work with a Yongnuo YN-622N-TX i-TTL?

A: The Vello FreeWave Fusion Basic 2.4 GHz Wireless Receiver will not work with the Yongnuo YN-622N-TX i-TTL

Q: 7. Is there a template for mounting

A: NO! Completely unnecessary! Figure the center of where you want the tv, left,right and up,down and mark it with a pencil. Before removing uprights spread them out to max and that is the most they can be mounted apart from each other on the wall. I would subtract an inch to avoid problems. Ideally you want to mount them 22-26 inches apart at the same height. It is all dictated by where your studs are located. Just dont mount to close together, less than 16 inches apart you best keep it centered all the time. Remove the uprights from the crossbars. You can use the same upright to mark both sets of holes. Your template. Use hardware capable of bearing the load(250lbs). If they are mounted at different heights as long as not to much. Half inch or so. There are screws at the top of each to level the bars perfectly. This is probably the BEST TV stand for sale anywhere! GOOD LUCK!!!

Q: 8. I see this display will hold 46-60" monitors. But can I put smaller monitors such as 32" on it?

A: This mount has a minimum VESA of 200x200mm. Most smaller monitors only have a 100x100mm.

Q: 9. Does this mount have an extension kit that can be added to make the three displays higher?

A: I'm sorry, it does not.

Q: 10. Does this mount supports 65" TVs as well ?

A: No, this Peerless-AV Portable Video Wall Cart is only for 46 to 60" Displays.