The FlashForge 1.75mm PETG Filament Red 1.1 lbis made with PETG, or polyethylene terephthalate glycol, which is stronger and more temperature resistant than PLA. It is also as strong as ABS, but with less warping and no odor. PETG is often used for applications that need to contain food and water. It is recommended that PETG be kept in a dry container. To reduce stringing, it is important to tune the retraction settings.

1.75mm Filament Diameter    PETG Material

Related Questions and Answers

Q: 1. Are these the Boas filled with regular steel shot, or stainless steel shot?

A: Boa Bags are filled with regular steel shot.

Q: 2. Can shotbags easily get through airport security?

A: Matthews Shot Bags are filled with steel shot and should have no issues making through airport security.

Q: 3. Can you not use a center column with this leveling base?

A: The Leveling Base replaces the center column. It is my default setup for tripod mount.

Q: 4. How tall is this when draped over a leg? Will it touch the ground if set on a 5.5" tall leg of a roller stand?

A: Unfortunately, a measure of this type is not published for the Matthews 25 lbs Shot Bag, as it would greatly depend on the exact roller stand that it is being used with.

Q: 5. I'm getting really low monitoring through headphones on this. even turned up to 10 and balanced to hear the preamp only. Does anyone else have this issue?

A: I haven't heard of this issue per-say. The first thing I'd look at would be the impedance specification on my headphones. If it's on the high side, I'd consider getting a headphone amp, or headphones with a lower impedance.

Q: 6. Does it work combining the Right and Left output into single mono output by using a Y-cable?

A: Yes, it does. I use it with GarageBand and both microphones are being used. I am a hypnotherapist and needed two mins to record both my client and myself and it works perfectly. Hope this helps.

Q: 7. what are the dimensions of the bag? Do they ship filled with shot?

A: It does indeed ship with shot -- and each bag is about 5 inches wide at the bottom seams and 1.5 inches at the top at the grippy part.

Q: 8. Hello,I need a lightweight battery powered preamp. It will be used for nature sounds recording with a matched pair Rode NT5 and a Tascam DP008EX recorder. This preamp doesn't have XLR outs bu 1/4'', and the recorder has 2 1/4'' inputs. Is it possible to use this preamp with my recorder?Thanks!Dani

A: Hi Dani,Yes, you can use the 1/4 outputs from the preamplifier to directly drive the 1/4 inputs in your recorder. you only need to buy or build two simple cables with plugs at both ends. As far as signal voltage levels are concerned, I don't expect any problem because you can comfortably adjust the preamplifier monitor level to prevent saturation of your recorder inputs (by the way, the 1/4 outputs and the 1/8 outputs both depend on the monitor knob). As far as equalization is concerned, I don't expect a problem either, assuming the recorder inputs have a flat response - i.e. are not designed for musical instruments (if the latter applies, you might need re-equalization during recording or playback, but I'd not consider this as a drawback). Therefore, this wonderful preamplifier meets your needs. Cheers from Italy.

Q: 9. Will this work as a headphone amp/ dac as well as microphone amp? Am wanting to improve sound from laptop to headphones

A: Do not understand what you mean with dac . If the purpose is to improve the laptop output, I suggest you look for something else, as this pre-amp was conceived for high quality Analog to Digital Conversion (ADC) from microphones. The headphone level you've got with this pre-amp is just for monitoring purposes during recording, thus the output level is quite comparable to what's provided by a laptop.

Q: 10. Can one use this simply as a stereo mic amplifier with a 9v battery and no USB connection?

A: The ART USB Dual Pre can operate as a standalone mic preamp using 9V battery or AC power.