The black Countryman I2 Saxophone Brass Mic Kit for Line 6 Wirelessfrom Countryman I2 Saxophone Brass Mic Kit for Line 6 Wirelessis a mic that has been built from the ground up for smooth frequency response, low noise, and precise polar patterns with deep nulls and natural on- and off-axis response. It can be used to capture natural audio for this instrument.

The I2 microphone is suitable for distance miking that is invisible in front of audiences and on camera. This version offers a standard sensitivity for close miking saxophones, horns, and brass instruments and features a flexible positioning arm for precise microphone placement. In addition, the 5' cable is hardwired to the mic and terminates with a TA4F connector for direct connection to Line 6 TBP12 wireless bodypack transmitters.

Cardioid Polar Pattern    For Instruments and Sound Reinforcement    Hardwired Connector    Natural On & Off-Axis Frequency Response    For Uncolored Recordings    Reduced Feedback Issues

The I2 maintains excellent pattern control and frequency response at all angles. It offers uncolored recordings and reduced feedback issues.

Flexible close miking techniques are aided by the instrument mounts, which position securely and gently on the instrument for capturing audio.

Small size and sonic precision makes this microphone suitable for X-Y, M-S, and other techniques that rely on accurate, coincident positioning and consistent patterns.

The cardioid polar pattern is effective for picking up sound directly in front of the microphone and is less sensitive to sound directly behind the microphone. It picks up about 1/3 less ambient noise than the omnidirectional polar pattern, so the working distance (the distance a performer could be positioned from the microphone) is approximately 1.7 times that of the omni. The cardioid pattern works best when you can position the microphone directly towards the sound you wish to record (a lead singer, for example) and directly away from unwanted sound sources like a crowd or a loud monitor).

Related Questions and Answers

Q: 1. Can the Whirlwind PressBox6 be fed by the LMPRE mic preamp to make an inexpensive mult box?

A: Yes, that set-up should work fine.

Q: 2. Would I be able to use this on my BMPCC 6k Pro?

A: Yes, you can use the the line-to-mic attenuator but it's not necessary since the BMPCC 6k Pro accepts line level audio through the 3.5mm inputs.

Q: 3. Wht is the difference between this cable and ACH4-25MON-RA?

A: The Right - Angle connectors.

Q: 4. Can I use this to add a headphone jack to my Panasonic G7 to monitor audio?

A: Yes you can. That is a cable to go from line level to mic level. Used so you can plug the output of a line level recorder out. Into a camera at mic level in. With a headphone jack.

Q: 5. Is the item compatible with the Sony A7s?

A: Yes it is. The Sony A7s has a 1/8 inch mic level input. The Kopul attenuator would be used coming out of a line level source.

Q: 6. Is the "direct out" before or after any trim/gain adjustment? Looking to boost 8 mic signals to 8 line level. Will this do it?

A: The direct output on the Rolls RM82 8-Channel Mic/Line Mixer is taken immediately after the preamp stage, before any signal processing or adjustments.

Q: 7. Hello, on the rear panel of the device is mentioned that power supply is 120V AC 50/60Hz but in Europe supply is 220V AC 60Hz.Can we connect this device on European power supply? Usually product that comes from USA have both 110/220V AC power supply.Thank you

A: this device has not have a switch to 220V, so i do not recomend that you connect it to a 220V.

Q: 8. Is the headphones female port trs or trrs and will this work with my Canon M50

A: The Kopul ACH4-25MON Line-to-Mic Attenuator Cable uses a standard 1/8" TRS connection for headphone monitoring and is compatible for use with the 1/8" / 3.5 mm TRS stereo microphone input on the Canon EOS M50 Mark II Mirrorless Camera.

Q: 9. wattage per channel?

A: The RM82 does not have any amplification. It outputs a line level signal.

Q: 10. What is the warranty? I have one a few years old and it's starting to have buzz issues.

A: Rolls rack mixers are covered by a limited one year warranty for parts and labor from the Manufacturer.