Enhance the dialogue of your favorite movies and TV shows with the ELAC Debut Reference Two-Way Center Channel Speakerwith black baffle & walnut cabinet from ELAC. When paired with your amplifier or receiver, it will primarily produce dialogue, while the rest of your speakers create the ambient sound effects. It accepts up to 120W of power and features a 55 Hz to 35 kHz frequency response. The speaker consists of a 1" cloth dome tweeter and two 5.25" woven aramid-fiber cone woofers, plus two front-firing, dual-flared slot ports for enhanced low-frequency reproduction.

Two-Way Speaker Design    Up to 120W Power Handling    1" Cloth Dome Tweeter    2x 5.25" Woven Aramid-Fiber Cone Woofers    55 Hz to 35 kHz Frequency Response    2x Front-Firing, Dual-Flared Slot Vents    Magnetic Fabric Grille Included

The Reference Series' waveguide and grille design enhance upper high-frequency response.

Two front-firing, dual-flared slot vents allow for lower noise and higher bass output for improved bass dynamics.

A full-perimeter brace that joins the top and side panels significantly lessens cabinet vibrations, minimizing cabinet coloration.

Dual cast chassis woofers provide improved stiffness for both strengthening the front baffle and minimizing chassis resonances.

Oversized ceramic magnets produce high motor strength for powerful bass reproduction.

The top and bottom plates are constructed from low carbon steel for high magnetic conductivity to maximize flux density.

Related Questions and Answers

Q: 1. Is Yamaha R-N303D Network Stereo Receiver capable of bringing out the best from this pair of speakers?

A: These are very sensitive 6 ohm speakers. The Yamaha R-N303D, while an excellent receiver, is not designed for 6 ohms, and is less than ideal. It can power the speakers, but could conceivably be damaged at high volume.

Q: 2. is this a single speaker wire? For 1 or 2 speakers? Other vendors have this as enough for two speakers. BH #ELRSPW10FTP • MFR

A: The ELAC Reference Sensible Speaker Wire with Dual Banana to Banana Connectors (10'), BH # ELRSPW10FTP, is designed for a single speaker input of a negative and positive conductor. Two of these cables would be required for a stereo pair of passive speakers.

Q: 3. Is possible to surface mount these to the ceiling to use as Atmos ceiling speakers? Thanks!

A: No. Wall brackets are included though.

Q: 4. Is a Onkyo TX-8020 Stereo Receiver good for this set?

A: Yes. These ELAC speakers will perform very well with your receiver: Onkyo TX-8020: 50 watts x 2 (stereo) into 8 ohms (20-20,000 Hz) at 0.08% THD

Q: 5. Is this speaker powered or does it require an amplifier?

A: An amplifier or receiver is required o power this speaker.

Q: 6. Do these ideally need max 120 watt input PER speaker or 120 total?

A: The maximum recommended wattage is 120w per channel.

Q: 7. Does a Dayton Audio SUB-1000 subwoofer pair with these or not needed for listening to music?

A: I do not see why not. The subwoofer choice is more defined by the size of the room and the the type of music listened to.

Q: 8. CAN I USE ELAC 2.0 A4.2 HAS REAR ATMOS SPEAKERS FOR dobby speaakers?

A: The ELAC Debut 2.0 A4.2 Atmos Add-On Speakers (Pair), BH # ELDA42BK, may be used for the Dolby Atmos channels.

Q: 9. Will these speakers work well as rear channel speakers with a system powered by a Yamaha RX-V485 receiver?

A: Yes they will very well as rear surround speakers.

Q: 10. What is the country of manufacture?

A: It is made in China.