Tecnec Wpl-1114Tb Stainless Steel Wall Plate

Tecnec Wpl-1114tb Stainless Steel Wall Plate

Product Code: eq7508
Availability: In Stock

$130.47 $193.10

Qty

19 reviews Write a review

Description
Reviews (19)

The TecNec WPL-1114TB Stainless Steel Wall Plateis a stainless steel wall plate featuring two Neutrik 3-pin male XLR connector terminal blocks. This high quality plate has counter-sunk mounting holes, allowing for a flush finish.

(2) Neutrik 3-Pin Male XLR Terminals

Parameters
Dimensions (WxHxD)	2.75 x 4.5" (7 x 11.43cm)
Packaging Info
Package Weight	0.2 lb
Box Dimensions (LxWxH)	3.9 x 2.8 x 1.1"

Related Questions and Answers

Q: 1. best glue to keep rubber tips attached to the tongs?

A: Loctite Marine Epoxy.

Q: 2. How big are the holes and what' the spacing? Was thinking of putting some magnets on this and want to get some ideas on sizes

A: The larger holes are 5mm, and the smaller 3mm. From center to center the large holes are 5.5 cm apart. From center to center the small holes are 3.5 cm apart. The entire plate is approximately 7.5cm x 14.5cm

Q: 3. Which hole is the "safety cable hole"?

A: safety cable goes on the Baby Pin

Q: 4. What size diameter is the holes or anchor points? I want to secure Kino clips onto them.

A: Think it is 1/4 inch and 1/8 inch for smaller

Q: 5. What's the difference between this and the identically named SRP-115?

A: This plate is the same as the SRP-115 produced by Impact.

Q: 6. Will this receive a full size C-stand riser?

A: Yes, the opening is 1 1/8 which is standard for most C stand columns.

Q: 7. What is the distance between the bigger holes on the short end?

A: From the center of each hole, we measured 65mm with a vernier caliper.

Q: 8. What are dimensions of the flat plate itself (not the receiver)?

A: The size of the plate is approximately 5.9x3.6".

Q: 9. Can this also be used as a junior pin?

A: Remove the screw and it should fit a junior receiver.

Q: 10. What is the dimension from the back of the plate to the far end of the receiver?

A: It is about 3 inches from the back of this plate to the far end of the receiver.

Tim the PM	24/09/2024
[0.2 lb] very durable w/perfect fit 5

Dominick	21/09/2024
[0.2 lb] It works great and hasn't died on me so far. 5

anyonymous	11/09/2024
[0.2 lb] I bought this for a sound system installation. It required multiple inputs and volume control at the source. The mic input is not tied into the volume control which is just how i wanted it. This was perfect for me. 5

Joseph D	05/09/2024
[0.2 lb] When developing film, Black & white or Color, the temperature is very important. This has always been a great accessory in the darkroom... 5

Tim	17/08/2024
[0.2 lb] What can I say, they are the right size, the right three, and the right quantity! It doesn't get any better than this. Seriously not the easiest size to find, and B&H has them, in both black and silver. 5

Scott	23/07/2024
[0.2 lb] Perfect for the Neutrik modules. 5

Immoe	18/07/2024
[0.2 lb] I use this to get the temperature to process C-41 film. It developed the film pretty good so I'm guessing this is accurate. Easy to use, although I don't like using the handle it comes with because it just gets in the way. 5

Kolton	25/06/2024
[0.2 lb] The plate looks great! 5

Joan	23/06/2024
[0.2 lb] This wallplate with the Male 3-pin XLR already installed was exactly what we needed to make our football broadcast great. 5

Franklin	21/06/2024
[0.2 lb] Great quality thermometer, it is stainless steel, great build. It measures temperature very quickly, no need to wait for a long time before the needle moves. Highly recommended for developing film using a tank. 5