The cocoa Countryman E6 Omnidirectional Earset Mic Low Gain TA3F Cocoais a vocal microphone with an adjustable boom that weighs less than one tenth of an ounce and is designed to be used by only one person. Once adjusted, it will continually hold this shape.

The E6 earset can be used on either ear for capturing audio and rejecting unwanted sound, feedback, or surrounding noise from stage monitors or nearby speakers in houses of worship, theater, and outdoor vocal and speech applications.

The low-profile, omnidirectional E6 earset virtually disappears against the skin, so performers will forget they're wearing a mic. This version offers the lowest gain for the most powerful vocals that require the highest overload. In addition, the earset comes with three protective caps with different high-frequency response characteristics that control the amount of crispness or sibilance (response at 15 kHz). This omnidirectional E6 earset's cable terminates to a TA3F connector for direct connection to Audix RAD360-BP wireless bodypack transmitters.

For Stage, Theater, and Broadcast TV    Fits Audix Transmitters    Headroom for Strong Vocals    Detachable 1mm Diameter Cable    Stiff, Steel Boom    Includes Windscreen    3 x Protective Caps    Black and White Single Tie Cable Clips    Carrying Case

The Countryman earsets are very small, lightweight, and the least visible headworn microphones.

The classic E6 is a good choice when one person will wear the microphone. Because the boom is stiffer, it can be adjusted to fit, then stored away and quickly reworn.

The E6's stainless steel boom is tough and can be bent and re-bent to fit different performers. It is highly resistant to makeup, sweat, and moisture when used with the supplied protective caps. The earset should always have a protective cap in place to keep sweat, makeup, and other foreign material out of the microphone.

The E6 earset's flexible boom is easily shaped right on the performer's face. Changeable protective caps let you shape the frequency response for different situations or to match other microphones. This omnidirectional version includes three protective caps—+4 dB (bright), +8 dB (very bright) and +0 dB (flat)—that controls the amount of crispness or sibilance (response at 15 kHz.)

Easy adjustment keeps the mic in a comfortable position for rejecting unwanted sounds. The omnidirectional E6 earset provides more isolation and is suitable for situations where there are loud monitors, extreme feedback, or environmental noise.

The included removable, quick-swap cable detaches from the actual earset, making it completely replaceable in the event of a short or break. The replaceable cable design makes upgrading wireless microphone systems easy as they are available in a wide selection of connections to accommodate most wireless transmitters.

Related Questions and Answers

Q: 1. Does this have a voltage regulator in it? I want to plug it into an Arri Alexa 3 pin which outputs 24-27v. IOW can I use a higher Voltage battery as the source such as a V-Lock (14.4v)

A: This dummy battery does not have a regulator. If you'd like to use A mount or V mount battery for continuous powering, please use it with LanParte Battery Pinch. The Battery Pinch is voltage regulated and offers several powering jacks with different voltage outputs for different gears.Please check out LanParte VBP-01 VBP-02 VBP-03(for V-Mount) or ABP-01(A-Mount)

Q: 2. I hear a lot of people recommending Canon LP-E6N's. Do the Canon batteries perform better than the BMD batteries, even at a lower capacity? Why wouldn't they just buy these?

A: the quality demand of Canon and other camera manufacturers are much higher the other makers. also they should last longer

Q: 3. Will this work with the EOS R5?

A: Yes, the Canon DC Coupler DR-E6 would be compatible for use with the Canon EOS R5 Mirrorless Digital Camera.

Q: 4. Is this compatible with 5d mark IV?

A: Not only did I check: I own it and use it with my 5D Mark IV without any problem at all!

Q: 5. Hello, I have a micro-battery LP-E6 that I bought for use with my BMCC4k, when I put it in my canon battery charger LC-E6, the light flashes without stopping and it seems that it does not charge the battery at all, do you know that it may be happening?

A: consider this charger , Watson Compact AC/DC Charger for LP-E6 & LP-E6N Battery B&H # WACCNLPE6

Q: 6. Trying to find a mount for a 13mm pin - will this work? What size is the hole?

A: The ProBoom® Ultima® Gen2 Ultra Low Profile Adjustable Mic Boom with a 12” fixed horizontal arm is a key building block in our modular mounting system for microphones and monitors. This single arm has a 29″ overall reach and supports microphones (not included) with a 1-5lb weight rating. Arm includes specialized angle limiting adjustment which allows for locked rotation ranges, but this product includes no mount (base stud size 13mm).

Q: 7. Do these work with the Mavic 3 Cine / Pro Remote?

A: No, the DJI Transmission High-Gain Antenna Set (4-Pack) are only compatible with the DJI High-Bright Remote Monitor, they are not compatible with DJI drone remotes.

Q: 8. How big is the slot for the base assembly? Will it work with other Booms?

A: This is designed to work specifically with Ultima Gen 2 Mic Arms. It may fit others but makes no claim.

Q: 9. will this work in a 6D?

A: Technically yes but you need to remove the door as I don't think it will close with wire there.

Q: 10. Will this coupler work with the AC adapter (brick) that comes as part of the Canon ACK-E4 AC Adapter Kit (for 1D3, 4, and X)? I already have several of those, so would like to just add the coupler (to fit a 5ds) rather than buy the whole ACK-E6 kit.

A: No, it will not work with the ACK-E4 AC adapter.