Designed for use primarily with the Joker 800 and Joker 1600, this K 5600 Lighting Focus Tube Baby Pin for Kurve 7from K 5600 Lighting Focus Tube Baby Pin for Kurve 7is a hollow tube, like a pin extender with a removable Baby pin on its end. Mount your choice of fixture and run its cable through the focus tube and out the back of the Kurve without dangling cables.

Compatible with 400, 800, 1K, 2K Lights

Related Questions and Answers

Q: 1. What’s the length of the 3/8”-16 thread?

A: The female thread is 35mm. The male thread is 20mm.

Q: 2. Is this the new updated version that can clamp without taking off the top of the cart?

A: Yes the Inovativ 5/8" Baby Pin System BH #INO500500 • MFR #500-500 has the clamp in the style that works over the tube for installation. You DO NOT have to take off the top shelf in order to use it.

Q: 3. I tried to use this on a c-stand with my elinchrom D-Lite 400W/s RX 4 Flash Head but the head does not fit on it properly. I bought the elinchrom in a bundle that included light stands. The elinchrom fits on the light stand perfectly. Now, I want to put the flash head on my c-stand. What are the proper attachments to do this to connect it to a c-stand?I bought the following products:a href= http://www.bhphotovideo.com/c/product/1086351-REG/elinchrom_el_20842_2_d_lite_rx_4_2_light.html target= _blank http://www.bhphotovideo.com/c/product/1086351-REG/elinchrom_el_20842_2_d_lite_rx_4_2_light.html/aa href= http://www.bhphotovideo.com/c/product/372016-REG/Impact_CT40MKIT_Master_Century_C_Stand.html target= _blank http://www.bhphotovideo.com/c/product/372016-REG/Impact_CT40MKIT_Master_Century_C_Stand.html/aThanks.

A: Your Elinchrom Head should fit on the 6-inch pin on the smaller, grooved, off-set end of the pin. But, first slide the small end of the pin through the appropriate-sized hole in the grip-head (on the arm extension) after turning the handle on the grip head to loosen the grip head and open the holes wide enough to slip the pin through. Then tighten the grip head handle to hold the pin in place, and to the angle you choose. Once that is done, you can then attach the Elinchrom head to the grooved end of the pin and re-adjust the angle and height.

Q: 4. The collar end is tapped, but not with 1/4-20 or 3/8-16. What is the spec of that tap?

A: From our measurements in the store with a caliper, it seems to be unthreaded and approximately 0.34" in diameter.

Q: 5. Your listing says the ballast is 'IN' the box and ALSO 'Not' in the box. Which is it? Please?

A: The Kit includes the ballast which is wireless DMX, ALS, Dimming, 1000Hz

Q: 6. What is the max weight this clamp can hold?

A: The manufacturer says there is no warranty or guarantee for the load limits of the Matthews C - Clamp with 2 Baby Pins - 10" BH #MACC1058.

Q: 7. The size of the clamp can fit the column (32mm diameter) of another Cart or not?

A: Sorry but we do not know the maximum diameter of the clamp but, according to Inovativ the Inovativ 5/8" Baby Pin System will fit on any Inovativ cart.

Q: 8. How much does this item weight?

A: The Impact Pipe Clamp weighs 1.37 lb (0.62 kg).

Q: 9. Can I use this with old joker 400 ballast?

A: Per conversation with K5600; it is backward compatible with all previous ballasts for the 400 series.

Q: 10. What is the pin length? 3inch?

A: The length is 3.5".