This 85 x 115mm LEE Reverse-Graduated ND Filter 85x115mm 2-Stopfrom LEE Reverse-Graduated ND Filter 85x115mm 2-Stopis compatible with a LEE Filters LEE85 System filter holder. It can be applied to darken bright skies, specifically during a sunrise or sunset, while allowing for a normal, unaffected exposure in the other regions of the image.

This filter achieves its effect with a 0.6 band of density above its center region that provides up to a 2-stop reduction in light from entering a lens. This band extends in both vertical directions which tapers to approximately a 0.15 density and a 0.5-stop reduction in light at the edge above it. Directly below the 0.6 band of density, it tapers to clear, with a hard-edged line of transition before the clear area.

The placement of a 0.6 band of density with a clear area directly below allows the LEE Filters 85 x 115mm Reverse-Graduated Filter to match the positioning of the sun when it is at, or immediately above, the horizon. In such instances, the sun can appear closer to the center of an image as opposed to the upper edge, and an increase in brightness is created which is more prominent on both sides of the sun than above it. This pattern of brightness corresponds to the density pattern on the LEE Filters 85 x 115mm Reverse-Graduated Filter. The hard-edged line of transition in this reverse-graduated neutral density filter is useful for hard transitions between the sky and land, while the 2-stop to approximately 0.5-stop gradation is applicable to multiple regions of brightness within the sky.

0.6 Optical Density    Optical-Quality Resin    For LEE85 System Filter Holder    Reduce Exposure for Sunrises or Sunsets    Maximum Density Above Center    Effect Configured for Sun at Horizon    Includes Padded Pouch

• Compatible with a LEE Filters LEE85 System filter holder
• Effectively darkens bright skies, specifically during a sunrise or sunset, while allowing for a normal, unaffected exposure in the other regions of the image
• 2-stop band of density that tapers to approximately a 0.5-stop density at the edge above it, while directly above a clear area
• Creates a neutral density pattern that matches the positioning of the sun when it is at, or immediately above the horizon
• Density pattern corresponds to the brightness pattern of the sun when it appears at or is closer to the horizon as opposed to a higher angle, which creates an increase in brightness that is more prominent on both sides of the sun than above it
• Hard-edged line of transition between the 2-stop band of density and the clear area below it is useful for hard transitions between the sky and land
• 2-stop to approximately a 0.5-stop gradation is applicable to multiple regions of brightness within the sky
• Filter does not affect the overall coloration of the image
• Constructed from optical-quality resin for clarity
• Padded filter pouch included for storage and transport

Related Questions and Answers

Q: 1. I currently have a sony A7r with a Sony FE 24-240mm f/3.5-6.3 OSS Lens. Is this filter compatible with the lens I am using? Are there any kits or adapters I need as well? Thanks!

A: Hi Christian, Yes, it will work, you'll just need a 72mm adapter for whatever filter holder you're using. My recommendation is a Lee Filter holder and a 72mm lens filter adapter. If you have a lens that takes a larger filter size, say a 77mm, then I'd get a 77mm adapter and a 77mm to 72mm step down ring. That way you don't have too many adapters. Hope this helps.mick

Q: 2. Will this fit NiSi 150mm Filter Holder for Tokina 16-28mm Lens ?

A: I bought it for the Lee Filter system.I have never used NiSi system

Q: 3. What is the normal F stop that is recommended for shooting with these filters? I just got the Big Stopper and the Super Stopper. Shooting with film.

A: Sweet spot on most lenses is between f11 and f16

Q: 4. Would these filters fit the Tokina 11-16mm f2.8 lens?

A: The specs for this lens, as listed at B&H, show a 77mm front thread. Get a Lee, or similar, 4x4 or 100x100mm filter holder and a 77mm wide angle adapter and it should physically fit. With this wide of a lens, I don't know how much vignetting you will get.

Q: 5. Will a Lee 150mm ND filter fit properly in an NiSi filter holder?

A: yes, it will fit nicely.

Q: 6. will this fit a Nikon nikkor 35km 1.8 and if so what accessories do I need to purchase with this filter?

A: yes with the Lee 100mm filter holder kit, go to 'Lee 100mm filter' on the internet and the site will show you everything you will need. I think B&H carries them.Regards...

Q: 7. Will Lee's Big Stopper work with the Tamron 14MM lens? And, what adapter ring would I use with it and the Lee Filters Foundation Kit?

A: I'm using Lee's Big Stopper with my cokin z pro filter holder for my Canon lens with two Cokin adaptor rings ( 82 mm and 77 mm). It works perfect for me. I don't have experience with Lee Filters Foundation Kit.

Q: 8. Will this fit the Haida M-15 filter holder?

A: Yes, the Haida M15 Filter Holder will hold the LEE Filters 150 x 150mm SW150 Solar Stopper Neutral Density 6.0 Filter (20 Stop) BH #LESSWQ • MFR #SW150SOL

Q: 9. Does anyone have a comparison on the Super Stopper compared to Lee's ProGlass 15 stop filter? Almost twice the price, is it worth it?

A: The LEE Filters 100 x 100mm ProGlass IRND 4.5 Filter (15-Stop) B&H # LEPGIRN15100 is more expensive because it combines two filters in one. Not only the ND but it also has an IR filter as well. Because digital sensor are susceptible to the infrared that get through the ND, this helps to keep your blacks from going to a very-hard-to-correct magenta color shift.

Q: 10. I want a Lee Big Stopper for my Canon EF 16-35mm f/2.8L II USM Ultra Wide Angle Zoom Lens. Which one do I need for that lens? What adapter and other equipment do I need? I also want the 3 stop and 6 stop Lee filters for this lens. Will I use the same adapter as for the Big Stopper?If not, what equipment do I need for them to use on the same lens?

A: You will need the LEE Filters Adapter Ring - 82mm - for Wide Angle Lenses. This will then attach to the LEE filter holder (which holds any 4x4 filter or 4x6 filter, such as the big stopper). The name of this kit is: LEE Filters Foundation Kit (Standard 4x4 , 4x6 Filter Holder). So, you attach the adapter ring directly to the lens (make sure not to have any UV or other circular filters attached or it will vignette), and then the filter kit attaches to that. You then slide in any LEE or other 4x4 filter you want.