This 12-pack of black Finishing Caps for EMBRACE Earmounts from Point Source Audio is designed to provide a neat finishing cap for the earmount when it is trimmed and customized for over-ear concealment. These finishing caps will fit any EMBRACE earmount.

For EMBRACE Earmount Microphones    Use for Customized Over-Ear Concealment    Provides Neat End for Trimmed Earpiece    Fits Any EMBRACE Earmount

Related Questions and Answers

Q: 1. Is this the same as ilfotol?

A: Yes the Ilford Simplicity Black and White Film Wetting Agent is exactly the same as Ilfotol.

Q: 2. What happens if you develop 2 35mm and then reuse it to develop 2 more?

A: The results could be less than ideal such as under developed and lower contrast negatives.

Q: 3. Can we reuse the fixer? For up to how many rolls?

A: A general rule-of-thumb would require you to test your fixer working solution immediately after mixing to find its clearing time, then when it takes twice as long as the original test to clear the film, you may discard it. In practice, to test your working solution, you can take an unexposed piece of film (such as the film leader) and place a drop of fixer on the emulsion side of the film. Leave it for approximately 20-30 seconds. Then place the film into the fixer, ensuring it is covered. Time how long it takes for the clear spot to disappear (when you can no longer tell the spot you placed the drop of fixer from the rest of the completely clear film). This would be the fixer's clearing time. You would double this time amount to find the amount of time it takes to fix your film (i.e., if it took 2 minutes 10 seconds for the film to become completely clear and the dot to disappear, you would fix film for 4 minutes 20 seconds). You would test your fixer every time before using the fixer. When, during your test, it takes twice as long to fix your scrap film leader to clear as it did when you first mixed the working solution, it may be discarded and you may make a new working solution. (if you wish, you may wait until it takes triple the time your original test took to clear, but this would result in extremely long fixing times).

Q: 4. What is the diameter of the hole?

A: The manufacture does not list the diameter of the hole for the Platypod Heavy-Duty Rubber Caps (4-Pack). It is made specific for the opposite end of a spiked foot on the Platypod. The return policy is 30 days. The link for that is, https://bhpho.to/2bxrYlG.

Q: 5. Would this light source cover both 35mm and 6X6?

A: Yes the Negative Supply Light Source Mini will scan 6x6cm negatives which is 2 1/4 Inch negatives. The scanning area is 3.75 x 2.5"

Q: 6. Is this a collimated light source?

A: The Negative Supply Light Source Mini is a calibrated light source. It features a high CRI of 97 for color accuracy.

Q: 7. How long will this last before it will go bad?

A: The Ilford Simplicity Black and White Film Wetting Agent (25mL) can be kept for 2 years unopened. Once opened they should be used immediately. If opened accidentally then immediately resealed it should be used within 6 months.

Q: 8. Will it go along well with Negative Supply Basic Film Carrier 120? Will carrier "snap-in" this?

A: Yes, the Negative Supply Light Source Mini is compatible with the Negative Supply Basic Film Carrier 120 (B&H # NEBFC120).

Q: 9. what is development time for HP5?

A: 6:30 at 68 degrees 5:30 at 75 degrees

Q: 10. can I use a sharpie permanent marker to write on a ceramic mug?

A: Yes but it will wash off in the washer very quickly unless you put a glaze over top of it. Simply baking it in the oven like you see on Pinterest doesn't last very long. Hope that helps, good luck with your project!