The 49mm Nisha Collapsible Rubber Hood 49mm Standardfrom Nisha Collapsible Rubber Hood 49mm Standardis designed to keep the sun or other bright light source off the lens surface to maintain proper contrast and color.

Rubber Made    Thread Mount Type

Related Questions and Answers

Q: 1. can you put an 82mm filter on the 82mm lens hood? like are there threads on the front (not just to mount it)?

A: The Sensei Collapsible Rubber Lens Hood II (Standard, 82mm) attaches to the lens via the front filter thread ring of the lens. It may also be attached to a filter with a front thread of the same size. The placement would be the filter first on the lens and then the hood on the filter.

Q: 2. Is this the best choice for the Nikon z40 f2 lens?

A: The Sensei 52mm Collapsible Rubber Lens Hood is a solid choice in a lens hood for the Nikon Z 40mm f/2 Lens.

Q: 3. will this lens hood work for a 82mm threaded Bronica/Nikkor H 50mm FL lens?

A: Yes, the Sensei Collapsible Rubber Lens Hood II will work with an 82mm threaded lens such as an 82mm threaded Bronica/Nikkor H 50mm FL lens.

Q: 4. Will this work with a side pinch cap?

A: Not very well. Cap pops off often.

Q: 5. will this fit on a Panasonic HC-V750EB-K Full HD Camcorder ?

A: Yes, this lens hood is compatible with the 49mm filter thread on the Panasonic HC-V750EB-K, however, keep in mind that you may experience some vignetting when zoomed out all of the way with this camcorder and lens hood combination.

Q: 6. I would like to purchase this hood for my olympus rc with a 40mm lens. It should fit but will it show in photos?

A: No, it won't show.

Q: 7. Can you use a lens cap with this lens hood attached? What size?

A: Hi Mackenzie.This is a fantastic product. I have one, and a B+W clear filter on all my lenses (mostly Zeiss). It makes the camera less intimidating, provides deep shade to the lens (better than the original), collapses at a touch and is very compact, and , to answer your question the original lens cap fits perfectly (at least for my lenses). To be perfectly clear, the filter screws onto the lens, the lens hood screws onto the filter thread, and when it is collapsed the lens cap goes onto the filter as if the hood were not there. I am sure it would be the same if you don't use a filter.The best thing is that even when collapsed it provides fantastic protections to the lens/filter surface, which is recessed about a centimeter, well away from sticky fingers and other hazards. As a result, apart from blowing off dust, the surface stays pristine and I virtually never need to clean a lens or filter.Highly recommendedPeter

Q: 8. What is the size of the front filter threads? I want to buy a lens cap to put on the front filter threads.

A: Same size, front & back.

Q: 9. Does this work with a Leica Q with a 28 mm fixed lens and no vignetteing

A: I'm going to mount this hood on a Voigtlander 40mm f1.4 with Fujifilm X-mount cameras, but according to my experiences, the shape of the hood might cause vignetting when you use a 28mm lens on a full frame camera, and maybe OK with a APSC cropped sensor cameras.

Q: 10. Will this: B+W 49mm #900 Rubber Lens Hood B&H # BWLHR49 MFR # 65-069598 Work with a 35mm lens on full frame; specificaly on Sony RX1(R) and without vignetting?

A: I shoot 35 mm film so I suppose one could say that I shoot full frame. I do not experience any vignetting. I have two or three of these and have used them for over 25 years. Obviously I like them.