The OZEN 20M E-Z LOAD Max Fluid Head 61.6 lb Payloadis a heavy-duty fluid head with the familiar placement of pan, tilt, and counterbalance controls to easily fit into your operating style. Built to fit the needs of filmmakers with cameras and rigs that weigh up to 61.6 lb, the 100mm ball base allows for fast leveling and provides a wide balancing platform, which is advantageous when working with long lenses. The head features a quick release plate with two 3/8"-16 threaded camera tie-down screws, and the camera platform has 2.36" of travel for balancing your camera on the head.

The nine steps of pan and tilt drag are independent of each other and allow for precise adjustment to match the needs of your shot. A zero setting for each axis provides completely free movement to create whip pans and tilts. Individual pan/tilt locks allow you to lock one axis while still operating the other. The counterbalance has 16 steps of adjustment, which allows you to further tune the head to match the shot and your operating style. A built-in illuminated bubble level is a useful tool in dim lighting conditions for quickly leveling the head. Removable pan handle rosettes on the left and right side of the head allow you to utilize both included telescoping pan handles at once.

100mm Ball    E-Z Load Max Quick Release Plate    Camera Platform Has 2.36" of Travel    9-Step plus 0 Pan and Tilt Drag    Independent Pan and Tilt Locks    16-Step Counterbalance    Built-In Illuminated Bubble Level    Dual Telescoping Pan Handles

A 16-step counterbalance allows you to adjust the head for a variety of cameras and rigs weighing from 8.8 to 61.6 lb. The counterbalance system is designed to neutralize the weight of the head, so the fluid head will hold the tilt position you leave it in without having to hold it in place. When tilting, you don't have to fight the resistance of the counterbalance during a tilt move.

With nine steps and a zero setting, you can adjust the head for smooth movement when creating fast or slow moves. The dampening settings allow you to adjust your setting from shot to shot, while the stepped settings make your drag selections repeatable.

The E-Z LOAD MAX QR plate supports heavier camera rigs, pops in and out of the camera platform, and does not have any sliding balance adjustment. However, the camera platform that the plate pops into has 2.36" of back and forth adjustment to aid in balancing your camera on the head. An optional baseplate or VCT system for greater balance capability is customary with larger cameras.

The 100mm leveling ball makes it quick to level the head on your tripod legs or other platforms. The large platform size allows you to adjust the balance of your camera and lens and keep the center of balance within the 4" wide platform, for smoother operation without straining the head.

Removable rosettes on each side of the fluid head allow you to attach the included pan handles for two-handed control. If damaged or stripped, the rosettes can be removed and replaced with new ones.

The head comes with one each 1/4"-20 and 3/8"-16 camera tie-down screw stored on the sides of the head, in addition to the two 3/8"-16 captured tie-down screws in the E-Z LOAD MAX QR plate.

Related Questions and Answers

Q: 1. What size is the thread on this pan bar?

A: That's not specified by the manufacturer at the moment.

Q: 2. What size are the threads on this pan bar?

A: That's not specified by the manufacturer at the moment.

Q: 3. Can this stand be used with a junior adapter for lights with a junior pin?

A: This stand will not accommodate junior adapters.

Q: 4. Does this product have a m12 thread or similar on top to be used with lighting clamps?

A: The stand does not have any threads to receive a clamp.

Q: 5. What are the dimensions of the pan bar (length and diameter) when full collapsed?

A: The pan bar itself (not the thicker section near the clamp and not the grip handle) of the OZEN Agile 5S S-Loc 75mm Fluid Head (B&H# OZAG5S) is approximately 3/4" (19mm) in diameter. The length of the pan bar including both the thicker section (where it starts) until the bottom end of the grip handle is approximately 15" (38cm) in length when measured from the start, to the elbow bend, and then from there to the opposite end of the pan angled bar.

Q: 6. Can this be used in a way where you could slide it along the track to reposition as needed?

A: The Kupo Strut Channel Adapter with 5/8'' Baby Pin is meant to be fixed within the strut channel, so repositioning it would involve unscrewing the bolt that secures it.

Q: 7. Can this bar be used on the Ozen Agile 15?

A: Yes the OZEN Extending Pan Bar PB-2 works with all Ozen Agile head models including the 15.

Q: 8. I see 2 different mid-level spreaders. Does this come with the barrel twist or lever?

A: The OZEN 100CF2HD 100mm Carbon Fiber Tripod uses flip brake levers.

Q: 9. This shows a mid-level spreader hook. Can you attach a mid-level spreader to this unit?

A: Yes, there is a midlevel spreader for the SHAPE Pro Video Carbon Fiber Tripod with 100mm Bowl & Fluid Head . It is the SHAPE Mid-Level Spreader with Rubber Feet for ST15 & ST20 Tripods BH #SHMLSF • MFR #MLSFs

Q: 10. I would like to install upright this arm on a dolly cam, can it be mounted upright instead of invert, even with some adjustment?

A: There is the Came-TV GS12 model that does support vertical installation. However the GS10 will only work as an inverted Stabilizer Arm. The following model supports upright mounting B&H # CAGS12 https://bhpho.to/3RpJyGS More info about the Came-TV GS12 https://bit.ly/3fithpV Installation is upright. Suitable for DJI Ronin S/S2；Zhiyun Webill/Crane 3; MOZA and Feiyu gimbals. https://bit.ly/3fithpV