The precise and fluid Arca-Swiss Core 60 MonoballFix Levelerfrom Arca-Swiss Core 60 MonoballFix Leveleris equipped with a double-dovetail clamp that is compatible with Arca-Swiss Classic plates, MonoballFix plates, and Arca-Swiss monorail cameras. The clamp easily locks down by switching the MonoballFix mechanism. The head works on arc movements that keep your camera centered over your tripod, so you never lose your center of axis. The X and Y axes each have +/-10° of micrometric adjustment, which is controlled by two geared telescopic knobs, which pull out if you are using a larger camera and can't reach the knobs. The head has 360° panning on both the top and bottom base, and the top pan has a scale for a repeated setup or for measuring intervals when creating a panoramic shot. The Core 60 can hold camera equipment weighing up to 44 lb, and with each movement you make, there is no need to lock a knob because of its self-locking gear.

Load Capacity: 44 lb    Adjustment Range +/-10° on X/Y Axes    360° Panning on Top and Bottom Base    Arc Movement Keeps Camera Axis Cantered    Geared Micrometric Movements    Self-Locking Movements    MonoballFix Locking Mechanism    Telescopic Control Knobs    Arca-Swiss & MonoballFix Compatible    Fits Monorails of Arca-Swiss Cameras

The leveling head can hold camera equipment weighing up to 44 lb.

The Core 60 is equipped with a double-dovetail clamp that is compatible with Arca-Swiss Classic plates, MonoballFix plates, and Arca-Swiss monorail cameras.

The clamp locks via its MonoballFix mechanism.

The head works on arc movements that keep your camera centered over your tripod, so you never lose your center of axis.

The X and Y axes each have +/-10° of micrometric adjustment, which is controlled by two geared knobs that are self-locking.

The geared knobs telescope out, so you can reach them when using larger cameras.

There is a 360° pan on the top and the bottom base of the head. The top pan has a scale for a repeated setup or for measuring turning intervals when creating a panoramic shot.

Related Questions and Answers

Q: 1. Can the Arca part of the clamps be rotated 90 degrees so the Arca grooves are in line with the bracket instead of at right angle to it?

A: Unfortunately, the Arca dovetail portion of the Arca Swiss L-Bracket MonoballFix Universal cannot be rotated 90°.

Q: 2. can this be installed directly on arca-swiss monoball p0 ballhead? is this compatible with universal arca-swiss standard plates?

A: Yes, you may use the Arca-Swiss MonoballFix Quickset Device listed above on the top of the Arca-Swiss Monoball P0 with Panning System, B&H # ARMPOPS. It is compatible for use with standard Arca-Swiss quick-release plates.

Q: 3. Can someone clarify the two different answers below - can the dovetails be rotated on each baseplate, to switch whether the Classic or the monoballFix dovetail is the one in line with the lens axis? When I look at the additional baseplate that can be purchased separately, it seems to have the dovetails mounted in the other direction, suggesting they can be changed...

A: Hello Jonathan, Yes I confirm the dovetails can be rotated on each base plate to switch whether the Classic or monoballFix. When the plate is mounted with the narrow width parallel to the optical axis, then you can mount it on monoballFix® quik-release. When the plate is mounted with the larger width parallel to the optical axis then you can mount it on an Classic quick-release. This system is called "Dual Base". Now this L-Bracket has not been designed to change or replace the rotable plates with others monoballFix® plate. However if you absolutely need to do it, that is possible (everything is possible at ARCA SWISS :-)) but I would like to alert you on 2 points which are obvious for us but may not be clear for all the people. 1- If you replace the rotable plates/dovetail by monoballFix® plate, the you will have to choose only the ones with the grooves on their top so they will perfectely fit with the L-Bracket bases (horizontal and vertical). The compatible references are 802284, 802283, 802280, 802281, 802282 that you can find on B&H website. 2- Then you will not be able to use the screws neither the one of your L-Bracket dovetail plate (it may be too long depending on your camera base mouth depth) nor the one delivered with the additional plate (it may be too short). In that case we can provide a custom solution with specific screws but it that case we need to make a prior analysis and eventually a special order with B&H. Hope it answer your question and if you need more support, please just ask. Jean-Pierre from ARCA-SWISS

Q: 4. Will this quickset plate fit the Arca Swiss Z1 ball head 801103?

A: Yes. But please keep in mind that the following adapts to smaller QR plates such as the following plates mentioned. 802255, 802260, 802262 and 802265.

Q: 5. Are the safety pin removable?

A: The pins are not removable by any normal means.

Q: 6. Does this fit the Hasselblad X2D?

A: Yes, the Arca-Swiss L-Bracket MonoballFix Universal is compatible with the Hasselblad X2D.

Q: 7. Does this work with the Smallrig L bracket?

A: Yes this will work with the Smallrig L bracket as it is the Arca Swiss type.

Q: 8. What is the maximum width for plates that can be held in this device?

A: The plate must fit the dovetail slot in this Quickset Device. I've found that the Quickset lever won't lock unless I had a camera plate that fit into the dovetail slot properly. I use an Arca Swiss 802260 Monoball Fix 32 Camera plate (the B&H # on my order was ARSF32C) with the Quickset Device - there are other Arca Swiss Monoball Fix 32 plates available as well. I've measured the 802260's camera plates dovetail with calipers and at the 'neck' of the dovetail, its 19.07mm and at the base of the dovetail 25.85mm The height of the dovetail from bottom of the dovetail base to the bottom of the camera plate is 5.45mm. When the Quickset Device has nothing in the dovetail slot and the lever is in the closed/latched position, the opening is 23.04mm (this measurement is at the location where the camera plate's dovetail neck would fit. When I push the lever as far open as possible, the opening is 25.12mm wide -- but the lever won't close if you fit something this big into the Quickset Device.

Q: 9. Will it fit Peak Design PROplate?https://a href= http://www.bhphotovideo.com/c/product/1096749-REG/peak_design_pl_pp_1_proplate_a_for_manfrotto.html target= _blank www.bhphotovideo.com/c/product/1096749-REG/peak_design_pl_pp_1_proplate_a_for_manfrotto.html/a

A: Yes the Peak Design PROplate is Arca-swiss compatible with this clamp, as well as Manfrotto RC2 compatible.

Q: 10. Does this take genral Arca-Swiss compatible plates?

A: The Arca-Swiss MonoballFix Quickset Device does not use standard Arca-Swiss plates. You need smaller than normal, MonoballFix camera plates like the Arca-Swiss monoballFix Cameraplate 48 Universal. Here is the link: https://bhpho.to/3vqjTqa