Canare 4S11 Speaker Cable 12' 4 Spade Connectoris audiophile quality and handcrafted with Canare 4S11, 11 AWG Starquad cable. Starquad virtually eliminates EMI while offering minimum resistance and excellent frequency response due to low capacitance. This cable is perfect for short or long speaker runs. This hand soldered cable is a heavy-duty locking 4 spade to 4 spade configuration. Canare Premium speaker cables are also available with heavy-duty spade lug connectors, and locking banana/spade connector combinations, as well as additional bi-wire configurations, and in bi-amp configurations where the amplifier has 2 sets of outputs and the speaker has 2 set of inputs. Bi-wire and bi-amp versions with banana, spade, and banana/spade combinations. Canare premium Speaker cables are perfect for use with any high-end, high-fidelity stereo speakers that require the best Locking Banana to Locking Banana connections.

Super flexible even in sub-zero temperatures

Special PE dielectric for great frequency response over long distance cable runs

Hand assembly with true silver solder in Guild Shop

Made with audiophile quality, Gold Plated Locking Banana Connectors

Great for Home Theater

Related Questions and Answers

Q: 1. What can I use to split the connection for two speakers into one output? One output from the preamp going to two speakers.

A: Generally, an output may be split to two speakers with a simple "Y" type cable. Isuues arise when the impedance is too low; for instance, id the two speakers are 4 ohm and split from one output, the impedance then becomes 2 ohms; an impedance this low is almost always an issue for an amplifier. Also by changing the impedance which an amplifer is "seeing" will affect the loudness, so be aware and proceed with caution. Two 8 ohm speakers connected to one output of an amp is almost always ok, using a quality Y splitter and quality cables. Again, it WILL get louder!!

Q: 2. Wouldn't this single Canare quad speaker dual banana to dual banana be sufficient alone to connect to a center channel speaker?

A: It would depend on the connectors on the back of the center-channel speaker that you want to connect to.

Q: 3. What is the brand of this cable? I know they use canare wire. Thanks.

A: These are Canare brand cables.

Q: 4. What is the exact model of this 4S11 or 4S11G cable? because one is OFC and the other is not!

A: I bought 4S11 (MFR # CA4S112B2B6). They are not fiber optic. You should call B&H if you're not sure. Customer service is very good.

Q: 5. What is the exact model of this cable 4S11 or 4S11G? because one of them is OFC and the other is not!

A: CANARE model number: CA4S112B2B6

Q: 6. Is this a standard 4mm Banana Plug?

A: The Canare 4S11 with Banana connectors are 4mm locking plugs.

Q: 7. Are these locking bans plugs on the canare brand?

A: Yes, the Canare 4S11 Star Quad Speaker Cable Dual Banana to Dual Banana (6') BH #CA4S112B2B6 has locking connectors.

Q: 8. Is this item a pair of 35' cables or just one 35' cable?

A: The Canare 4S11 11GA Star Quad Speaker Cable is one 35' cable with two banana plugs on each side.

Q: 9. What is “stranded annealed copper conductors” - in the description ?

A: Annealing is a heat treating process that makes copper wire flexible and it also improves its conductivity -- the ability to send electronic signals through the wire. The internal copper wire conductors used to construct this audio cable are made up of individual thin strands that are bundled together to form one larger copper conductor wire which is then covered with insulation. While standard audio cables typically have two internal conductors, Star Quad cable is constructed with four separate conductors, each made up of bundles of stranded copper wires and insulated. The four-conductor construction of Star Quad cable is used to deliver a strong audio signal with high-quality sound that is free of external noise.

Q: 10. is the entire cable covered with braided sleeve or just where the cable split with red(+) & black(-)?

A: The entire cables are braided.