Add a professional, high-capacity battery plate to power your Sony FX6 rig and accessories with this V-mount Wooden Camera Battery Slide Pro Sony FX6 V-Mountfrom Wooden Camera. The battery slide attaches to the rear of the camera and supports a V-mount battery while leaving access to the camera's standard battery compartment. With the camera's BP-U battery in place, hot swapping is supported.

The Battery Slide Pro also features three D-Tap outputs for powering accessories. The D-Tap array features a digital fuse that monitors the individual D-Tap ports and disables them if they exceed the set current for accessories, leaving the camera running without interruption. Once the load has been reduced by removing accessories, a reset button can be pressed to enable accessory power again.

Once the slide is mounted onto the camera, the battery plate position can be adjusted by loosening a lever and sliding the plate. The assembly closely matches the rear profile of the camera to allow it to efficiently fit in a camera case.

Attaches to Rear of FX6 Camera    Supports V-Mount Battery    Access to BP-U Battery Allows Hot Swaps    3 x D-Tap Ports, Protective Digital Fuse

Sony FX6 camera
V-mount battery

Related Questions and Answers

Q: 1. Does the plate have enough clearance if you use in tandem with IDX 98 BP-U batteries?

A: This is for one V mount battery.

Q: 2. Will this work with the 26 volt V-Mount batteries like it does with the 14 volt ones...converting the output to 19.5 volts?

A: The Anton/Bauer Micro Battery Slide Pro for Sony FX6 (V-Mount) is designed to only work with 14V V-mount batteries.

Q: 3. Can the slide assembly be lowered on the bracket that attaches to the camera? In other words, can the battery mount be lowered?

A: The battery plate portion of the Anton/Bauer Micro Battery Slide Pro for Sony FX6 (V-Mount) can be adjusted vertically along the camera connection arm using the large tightening knob, which when released will be able to slide along the light of the plate in it's open rail. This is best shown in the final two images where you can see the open rail that the screw would slide along just below the knob itself.

Q: 4. I lost the screws for this piece of equipment. Where can I find replacements?

A: We recommend connecting with Anton Bauer support for the replacement screws. salessupport_USA@vitecgroup.com

Q: 5. Is this the same model that was used for the Sony FS7?

A: The Wooden Camera Battery Slide Pro V-Mount for Sony FX9 is only designed to work with the Sony FX9.

Q: 6. Is the same one that came out for the Sony Fs7?

A: No, the Battery Slide Pro V-Mount is designed and made for the (Sony FX9) only.

Q: 7. Weight of this please?

A: This should weight right around 1 pound.

Q: 8. Do they make one for the Sony FX9?

A: There is the Dual Micro Bracket for Sony FX9 from Anton Bauer. https://www.bhphotovideo.com/c/product/1627027-REG/anton_bauer_8375_0243_fx9_bracket_gm.html

Q: 9. What are the sizes of the two screws that secure the slide to the camera?

A: The screws that would be used to secure the Wooden Camera Battery Slide Pro for Sony FX6 (V-Mount) (B&H# WO283000) to the FX6 body appear to be M4 (i.e. 4mm metric) ones. The easiest way to tell that is to see if a standard 1/4" screw (used for mounting just about every type of non enormous camera to a tripod or quick release plate) is about the right size but doesn't thread properly after a couple of turns into the thread. (That should only be done very gently.) If so, that tap is indeed an M4 female thread. If the 1/4" screw is too large to fit in the tap at all then it's an M3 screw.

Q: 10. Will the indie pro v mount batteries work with this adapter?

A: yes they will.