The DITEK 66 Block Surge Protector Snap-It Series 2A 30Vfrom DITEK, which has a maximum continuous current of 2A and a service voltage of 30V, is designed specifically for voice/data professionals. The Snap-It provides both voltage and current limiting in addition to surge protection up to 1000A. Note that each 66 Block requires one separately purchased ground bar.

Quick Connect Module    66 Block Connector    30V Service Voltage    47V Clamping Voltage    2A Max Continuous Current    Tip-Ground & Ring-Ground Modes    Field-Replaceable    Built-In Diagnostic Test Points    Made from High-Impact Plastic

Related Questions and Answers

Q: 1. how long is the power cord, need a power strip with a 25 ft board?

A: The cable length for this unit is 14.5 ft long.

Q: 2. What’s a safe extension cord for this? I only need two more feet!

A: You can use the Hosa Technology Extension Cable with IEC Female Connector - 18 AWG, Black, 3' (B&H # HOPC183) or Watson 18 AWG Universal Power Cord - NEMA 5-15P to IEC C13, Black, 3' (B&H # WAPC183B).

Q: 3. Are the outlets spaced far enough apart so that I could squeeze a couple of wall warts in there along with some regular sized plugs?(what is the distance between adjacent outlets)

A: The spacing is decent, enough for a wall wart and a plug, but not two wall warts directly side by side. I had wall warts plugged in on the ends with normal plugs in the centers.

Q: 4. Is this rated for 240v ?

A: Hi the furmen M-8X2 does not work on 220 V i dont think furmen makes a unit like that the M-8X2 is made to work on 110 to 120 V thankyou the M-8X2 works very welland is a grate unit

Q: 5. I'm building a new house and will have the house mostly wired. Will this unit benefit me than an ordinary power outlet strip, in my rack, vs. a non-conditioned power strip?

A: Yes, This unit will help. I am a musician and we sometimes play in old buildings with dirty electricity. Played twice in the same old building: once without the unit and once with it. This unit eliminated most of the unwanted noise and interference caused by the less than satisfactory power source.I also have one in my home studio. It makes my power smooth, even and quiet. I plug surge protectors into the unit and then the equipment into the surge protectors.

Q: 6. Why is it recommended to put this at the top of a rack? I'd like to keep my Blackmagic monitor on top for visibility, and have this at the bottom, under an ATEM and Hyperdeck.

A: It is recommend to position the power conditioner on top, to dissipate heat better.

Q: 7. Length of power cord?

A: 66 inches long, a full 5 1/2 feet

Q: 8. Will the Furman M-8x2 Merit Series help clean up 6KW portable generator power?

A: This device is rated for Pro Audio devices. It cannot handle any product with a kilowatt rating.

Q: 9. Would this be good to use to protect a Drawmer MX60 unit and similar AV gear? Else anything else you can recommend?

A: Yes, the Furman M-8x2 Merit Series 8 Outlet Power Conditioner & Surge Protector is a good option to use to provide clean power and protection against power surges for the Drawmer MX60 Preamp and other A/V gear. If you need rack lights, you can get the Furman M-8Lx Merit X Series 8 Outlet Power Conditioner & Surge Protector - with Dual Rack Lights (B&H # FUM8LX), which is the same item with a pair of pull-out lights that have a dimmer control. The Radial Engineering Power-1 Surge Suppressor and Power Conditioner (B&H # RAPOWER1) is similar to the M-8x2 and the Furman P-1800 PF R Power Conditioner/Surge Suppressor B&H # FUP1800PFR) is specifically for use with instrument amplifiers and other high-current equipment such as amplifiers and powered monitors.

Q: 10. where made?

A: This product is made in China.