The Miller Air SOLO-Q 75 Carbon Fiber Tripod 2-Stageis a lightweight fluid head for the videographer on the go. Designed for cameras between 4.4 and 11 pounds, this die-cast aluminum alloy and rigid composite polymers head is dust and moisture sealed for smooth operation in harsh environments. The sliding camera plate allows 2.36" of balance adjustment, has screw slots, and it comes with a 1/4"-20 and 3/8"-16 camera tie-down screw as well as a combination 1/4-20 screw with locating pin.

Two-steps of counterbalance help you tune the AIR Fluid Head to match the needs of the shot. The fixed pan and tilt drag remains consistent throughout the head's operating temperature range of -40 to 149°F, and each axis has its own independent lock. Featuring a 75mm half-ball leveling base you can use this head with 75mm bowl base tripod legs, or remove the ball leveling stud for flat-base mounting.

Air Fluid Head, 11 lb Payload    2-Stage Tripod, 69.5" Max Height    75mm Half Ball Leveling Base    Fixed Pan and Tilt Fluid Drag    Independent Pan and Tilt Locks    Soft Carry Case

Miller fluid head pan and tilt technology

Suitable for payloads between 4.4 to 11 lb

Built for rugged outdoor shooting conditions

Removable stud allows the head to be mounted on a solopod and slider via a 3/8" thread

Optional second pan handle mount

Related Questions and Answers

Q: 1. can i screw and manfrotto 502 head on this?

A: If the head comes with 75mm half-ball, then yes you can. Otherwise you would need a 75mm half ball. I'm using Manfrotto 520 and it works fine with a bit of greasing.

Q: 2. Can i take out the mid level spreader simply without any tool, is it easily removable? That would come handy if i want to go lower with the tripod

A: Yes, the following spreader can be removed and replaced.

Q: 3. Will the Manfrotto 608 Nitrotech fit on this tripod?

A: You will just need a 75mm half ball adapter to use that head on this tripod. https://bhpho.to/31OOD4c

Q: 4. Will the Manfrotto 504HD head fit on this tripod? https://a href= http://www.bhphotovideo.com/c/product/683559-REG/Manfrotto_504HD_504HD_Fluid_Video_Head.html target= _blank www.bhphotovideo.com/c/product/683559-REG/Manfrotto_504HD_504HD_Fluid_Video_Head.html/aDo I need any adapters?

A: It should fit, I used it with Manfrotto 502 and 516 fluid head. This is one of the best designed tripods I've ever used. One lever controls both leg extensions at the same time. Very quick setup.

Q: 5. it says it has an 88LB capacity, but amazon has it rated for 9LBS?

A: Hello,My manager sat on the bowl, and he weighs probably about 120 lb. Amazon is quite wrong, or may be referencing the recommended payload of a kit, which bases max load off of the head. Recommended payload is 88 lb., but it can physically exceed that, though it won't be working optimally and runs the risk of a slip or collapse.

Q: 6. It says with 75mm ball but see the ball nowhere in any of the photos of descriptions. Rather it says 75mm bowl. Does this version come with a ball?

A: This product doesn't include a tripod head. You can get the same version with the head.

Q: 7. Do the legs slide out on their own or do you have to pull them out?

A: How many turns does it take to go from tight to loose enough for leg slide? Thanx!

Q: 8. How does this tripod hold up after long terme use? I've read the rubber feet fall off easily after a while. How about the locks, do they stay secure over time?

A: This is a good entry level tripod and will work as expected. If you have a long term project with anticipated hard use, you may wish to invest in a tripod meant for such use.

Q: 9. Hi! I plan to use this tripod with a Sachtler aktiv fluid head, but for that I need to make sure of the compatibility. There is a centered hole in the bowl where the head is mounted and I would like to know it's diameter. Could you please check it for me?

A: Yes. The following unit will adapt to the 75mm bowl drop.

Q: 10. Is it me going blind, or does it not indicate the maximum height of this tripod?

A: This tripod will reach a range of 15 to 80".