Made of injection-molded ultra-high-strength polyethylene, this SKB Cases R-Series 2621-10 Wheeled Waterproof Utility Case is made to withstand the most extreme and demanding shipping, handling, and working conditions on the planet. The case is offered here with an empty interior to allow for full use and customization of the interior space. To accommodate a wide assortment of gear, this case has an interior that measures 26.4 x 21.4 x 10". Two low-profile hinged handles allow you to carry the case by hand, or if it's too heavy you can extend the pull handle and tow the case behind you on its two skate-style wheels.

Design features include gasket sealing to an IP67-rating that makes the case dust and waterproof, a molded-in hinge for added protection, and six latches arrayed on three sides of the case that compress the gasket in the lid to seal it against water and dust. It is further resistant to a variety of hazards that you may encounter such as impacts, ultraviolet (UV) radiation, solvents, corrosion, and even fungi. A pressure relief valve comes into play especially during air transport by regulating the internal pressure, keeping your gear and the case from getting crushed and allowing you to open the case without having to break a tough pressurized seal that may develop.

Airtight and Waterproof to Mil Specs    Large 26.4 x 21.4 x 10" Interior Space    Built for Extreme & Demanding Conditions    Empty Interior for Full Customization    Polypropylene Copolymer Resin    UV/Solvent/Corrosion/Fungus Resistant    Telescoping Pull Handle with Wheels    Low-Profile Recessed Latches and Handles    Built-In Pressure Relief Valve    Molded-In Hinge and Padlock Holes

Related Questions and Answers

Q: 1. Would this case be good with a Nikon D610 with battery drive attached? How would I position the camera properly?

A: The advantage with this case is the lenses can be transported vertically and thus you can get more long lenses in one case. Regarding the D610 with grip, it is about 6.5 tall. Since the case is 9 deep, I would suggest adding 2-3 of foam to the compartment for the camera/grip so you can place it base down. Then it will not be jostled. I suggest a similar action for the other compartments if needed.

Q: 2. What are the exterior dimensions?

A: Hello Aron The Exterior Dimensions of the 2SKB-4812WS are: 50" x 13.375" x 12.75".

Q: 3. What are the interior dimensions (L x W x H)? Thank you.

A: Interior Dimensions 48 x 12 x 11" / 121.9 x 30.5 x 27.9 cm

Q: 4. Can this be checked as airline baggage?

A: The SKB 3i-Series 4213-12 Wheeled Waterproof Utility Case is 45.51 x 16.02 x 12.95" which is about 75 linear inches. Most airlines have a limit of 62 linear inches for checked luggage and 45 inches for carry on. Please contact your airline for more specific information as well as alternative options they might be able to offer.

Q: 5. Will this qualify as carry-on luggage?

A: Its exterior dimensions exceed typical carry-on restrictions, so it will likely need to be checked in. However, I would recommend checking with your preferred carrier to see if they make special accommodations based on your flight class.

Q: 6. How much does it weigh?

A: The weight of this case is 22.71 lb / 10.3 kg.

Q: 7. What are the interior dimensions of this SKB case?

A: The following are the interior dimensions from the SKB website: Interior Length: 50.50 in (128.27 cm) Interior Width: 14.50 in (36.83 cm) Interior Depth: 6.00 in (15.24 cm)

Q: 8. does this hold one kit or multiple kits?

A: According to Teradek: "This case is for Bolt XT 500/1000/3000 or XT Sidekick Sets, It can fit 1 TX and up to 2 RXs with or without dual Canon/Sony battery plate." https://teradek.com/products/protective-skb-case-for-2-bolt-xt-rx?variant=13699845947437

Q: 9. If the depth of the case is 16 then what is the depth at the top? The case is curved making it deeper at the bottom vs the top.

A: SKB Deluxe ATA Staff Golf Travel Case (Black, Wheeled) top depth is 10.5inches while the depth on the bottom is 16.5 inches.

Q: 10. Will the 12' manfrotto alu master stacking stands fit in the SKB 4213-12?

A: Hi Eric, I haven't tested that particular stand so I can't say for certain. Just to confirm I believe you're talking about model number 1004BAC. It looks like the collapsed height is 42.13 . The internal measurement of the case with the padded dividers is close to 41.5 . If you put the stand in at an angle it might fit. Besides that you could also look at our 3i-4719-8B-L case. That would come with layered foam so you could cut compartments for the stands and other gear. Thank you,Will