The StarTech Adjustable Rackmount DIN Rail Kit with Top Hat, Mini, and G Rails makes mounting your DIN-rail equipment in a 19-inch server rack/cabinet or wall plate simple without wasting space due to special bracket requirements for each piece of equipment. This TAA-compliant product adheres to the requirements of the US Federal Trade Agreements Act (TAA), allowing government GSA Schedule purchases. This 19-inch DIN Rail Mounting Kit includes the three most commonly used DIN rail systems: Top-Hat, Miniature Top-Hat, and G-Type.

ript>

Includes 3 Common DIN Rail Systems    Top-Hat, Miniature Top-Hat, and G-Type    TAA Compliant

Related Questions and Answers

Q: 1. Will these work on Proaim Victor carts?

A: As per the Manufacture the Inovativ Hi-Hat Rails for Apollo Carts are designed for the For Apollo 40 and Apollo 52 Carts.

Q: 2. I have lenses for a Sony a6000. The lens diameters indicate I buy the micro size, but the hood diameters suggest the mini size. Which measurement should I go by?

A: Since I do not have the camera, I cannot say exactly, but I think it depends on how lose you want the hat to fit. They are supposed to stretch onto the lens, so you want to buy one that is smaller than the lens diameter. But I know myself that they can be hard to put on if they are too snug and require too much stretching. But then they stay on better, of course, so it IS hard to tell. I think I'd go with the smaller one, especially if the lens is shallow - i.e. not very long. If the hat is too big and just kind of loosely holding on, it will probably be falling off if the lens isn't very long. Just MHO.

Q: 3. How do you under sling this Dana?

A: You can put the Dana Dolly Hi Hat Universal Kit in an underslung position by first removing the low hat by unscrewing the thumb screws from the sled, flipping the low hat, and then securing the low hat by screwing into the 4 countersunk mounting points.

Q: 4. Could you provide the pinouts of the Mini-DIN to the lightning connector?

A: Unfortunately, this is not public information at this time. The Mini-DIN connector is designed for our Mini-DIN compatible products. We do not suggest using these for third party products as we cannot guarantee success. Please feel free to reach out to our team for more information here: https://www.ikmultimedia.com/contact-us/

Q: 5. can that Reverse setup when wanna low angle?

A: For a low angle, you would want to use a shorter stand, such as a set of Avenger Combo Steel Stand 10s: https://www.bhphotovideo.com/c/product/611470-REG/Avenger_A1010CS_A1010CS_Ultra_Low_Boy.html/specs

Q: 6. Will these work with Inovativ Voyager carts?

A: The Inovativ Hi-Hat Rails for Apollo Carts BH #IN500590 are compatible with the Apollo carts.

Q: 7. Will this fit a 58 mm diameter lens

A: It's a bit tight, but yes it does fit on a 58mm lens.

Q: 8. Can you lay the tracks on the ground without using stands?

A: Yes, the dolly track holders can sit on the ground.

Q: 9. Will this fit a Leica Q2 Monochrom with hood attached?

A: The OP/TECH USA Hood Hat, Mini is designed to cover interchangeable lenses with a diameter of 2.5-3.0". This would be more than sufficient for the Leica Q2 Monochrom Digital Camera: B&H # LEQ2M.

Q: 10. Is there a way to see the 8 pin connector end? My insane audio tj 1002 deck has an 8 pin mini din connection out of the back for an iPod, but the supplied cord is for the old iPod 30 pin connector. I am looking for a 8 pin mini din cord that will fit the port on the back of my deck, with a lightning connector on the other end.

A: This cable is designed for IK Multimedia products. Unfortunately, this means this may not work with your situation here. Looking at the cable, this offers 7 pins. Check out an example of a product this will work with at the link below.a href= http://www.ikmultimedia.com/irigproduo/ target= _blank http://www.ikmultimedia.com/irigproduo//a